GRAPHTEC FC8000 Series - Page 264

16
16-1
INDEX
Symbols
(Cross Cut) ................................................................... 3-14
(Front Loading) ...............................................................
2-9
Numerics
2-pen .............................................................................. 1-3
2POINTS .................................................................. 5-6, 6-2
2POINTS. ...................................................................... 5-12
3POINTS .................................................................. 5-6, 6-2
4POINTS .................................................................. 5-7, 6-2
AlphabetGroup
A
accessory ....................................................................... 1-2
AC line inlet ....................................................................
1-4
AC power cord, 2/3 prong adapter ................................
1-2
Adjusting for the Registration Mark Scan Position .......
5-24
Adjust Manually ............................................................
5-36
Adjustment Marks ...........................................................
6-2
Adjust the Blade Length Automatically ........................
2-36
Adjust the Blade Length Manually ...............................
2-31
Advanced Registration Mark Sensing System ...............
5-1
After Turning on the Plotter ................................................
v
Aligning the Push Roller ...............................................
2-13
Aligning the Push Rollers .............................................
2-13
Alignment registration mark ...........................................
5-8
Apparel (AP) Mode .......................................................
4-14
Area sorting ....................................................................
8-2
Assembling ..................................................................... 1-5
Assembling the Stand ....................................................
1-6
Attaching a Tool ..............................................................
2-4
Attaching the Loupe .....................................................
14-2
Automatically Adjust .....................................................
5-34
Automatically Cross Cut ...............................................
3-16
Automatic Pre Feed ........................................................
8-4
axes adjustment (3POINT detection) .............................
5-7
axes adjustment (4POINT detection) .............................
5-7
axis adjustment (2POINT detection) ..............................
5-7
Axis Alignment, Cut Area .............................................
14-2
B
Blade Application and Features ..................................... 2-3
C
Changing and Storing RS-232C Settings ....................... 9-7
Changing CONDITION No. ............................................
3-6
Changing the Hold-down Force ...................................
2-14
Circle-Command Resolution Setting ............................
11-9
Cloth basket ...................................................................
1-9
Command ..................................................................... 11-2
Confirm the Cutting Data ............................................
13-19
Connecting with Network (LAN) .....................................
9-3
Connecting with RS-232C ..............................................
9-6
Contents of Operation from CONDITION Key ..............
2-19
Contents of Operation from Menu Screen ....................
2-19
Continuously Move Manually ..........................................
3-3
Control Keys .................................................................
2-17
Control Panel ................................................................
2-17
Control panel ..................................................................
1-3
control panel .................................................................
10-7
Copy (Duplicate Cutting) ................................................
4-9
COPY key .....................................................................
2-17
Cross Cut ......................................................................
3-16
Cross Cut Force ...........................................................
3-17
Cross Cut Manually ......................................................
3-15
Cut Line Pattern ............................................................
7-15
Cut off the Roll Sheet (Cross Cut) ................................
3-14
Cutter Blades .....................................................................
iv
Cutter Pen .......................................................................
2-2
Cutter Pens ........................................................................
iv
Cutting Area ...................................................................
4-2
cutting area ....................................................................
4-4
cutting area, ...................................................................
4-4
Cutting groove ................................................................
1-3
Cutting mat .....................................................................
1-3
Cutting Tests ........................................................
2-34, 2-35
Cut Width ......................................................................
3-14
D
Display Language Setting ............................................ 10-2
Distance Adjust ............................................................
7-13
Distance Adjustment Between the Registration Mark ..
5-14
Dual Configuration ........................................................
4-12
E
each cutter blades ....................................................... 2-27
Enabling/Disabling 1/2 Pen Check (CHECK TOOL) ..
14-16
Enabling/Disabling the ":" and ";" Commands
(COMMAND ":",";") ......................................................
11-6
Enabling/Disabling the Media Sensors
(MEDIA SENSOR) ......................................................
10-4
Enabling/Disabling the Pen Select Command .............
11-4
Enabling/Disabling the Push Roller Sensors ................
10-5
enlarge/shrink scale .......................................................
4-8
ENTER key ....................................................................
2-17
F
Fan Suction Setting ...................................................... 10-6
Force ............................................................................ 3-17
G
GP-GL Command ................................................ 11-5, 13-6
GP-GL Command Error Display ...................................
13-4
Grit roller .........................................................................
1-3
Grit roller position guide .................................................
1-3
Guideline to Set Offset .................................................
2-27
Guideline to Set Pouncing ............................................
2-27
H
How to Use Control Panel ............................................ 2-17
HP-GL ............................................................................. 3-9
HP-GL Command ................................................
11-8, 13-7
HP-GL Command Error Display ...................................
13-4