EasyManuals Logo

HP xw4600 User Manual

HP xw4600
176 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #133 background imageLoading...
Page #133 background image
Solving network problems
The following table provides fixes for common network problems.
Table 5-12 Network problems
Problem Cause Solution
Wake-on-LAN feature is not
functioning.
Wake-on-LAN is not enabled. Use the network control application to enable Wake-on-
LAN.
Network driver does not detect
network controller.
Network controller is disabled. Run the Computer Setup (F10) Utility to enable network
controller.
Incorrect network driver. Review the network controller documentation to verify the
correct driver, or obtain the latest driver from the
manufacturer’s website.
Network status link light does not
illuminate or never flashes.
The network status light does not
flash when there is network
activity.
No active network is detected. Verify cabling and network equipment for proper
connection.
Network controller is not set up
properly.
Use the network control application to verify that the
device is working properly.
Network driver is not properly
loaded.
Reinstall network drivers.
System cannot auto sense the
network.
Disable auto sensing capabilities and force the system
into the correct operating mode.
Diagnostics reports a failure. The cable is not securely
connected.
Be sure that both ends of the data cable are securely
connected.
The cable is attached to the
incorrect connector.
Be sure that the cable is attached to the correct connector.
There is a problem with the cable
or a device at the other end of the
cable.
Be sure that the cable and device at the other end are
operating correctly.
Network controller interrupt is
shared with an expansion board.
Under the Computer Setup (F10) Utility Advanced menu,
change the resource settings for the board.
The network controller
is defective.
Replace the NIC.
Diagnostics passes, but the
workstation does not
communicate with the network.
Network drivers are not loaded, or
driver parameters do not match
current configuration.
1. Be sure the network drivers are loaded and that the
driver parameters match the configuration of the
network controller.
2. Be sure the correct network client and protocol is
installed.
The network controller is not
configured for this workstation.
Double-click the Network icon in the Control Panel and
configure the network controller.
Network controller stopped
working when an expansion
board was added to the
workstation.
Network controller interrupt is
shared with an expansion board.
Under the Computer Setup (F10) Utility Advanced menu,
change the resource settings for the board.
The network controller requires
drivers.
Verify that the drivers were not accidentally deleted when
the drivers for the expansion board were installed.
ENWW Customer Self Help 125

Table of Contents

Other manuals for HP xw4600

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP xw4600 and is the answer not in the manual?

HP xw4600 Specifications

General IconGeneral
Tcase72.4 °C
Bus typeFSB
SteppingE0
Processor cache6 MB
Processor cores2
Processor modelE8400
System bus rate- GT/s
Processor familyIntel® Core™2 Duo
Processor seriesIntel Core 2 Duo E8000 Series
Processor socketLGA 775 (Socket T)
Processor codenameWolfdale
Processing Die size107 mm²
Processor frequency3 GHz
Processor cache typeL2
Processor lithography45 nm
Processor manufacturerIntel
Processor front side bus1333 MHz
Processor operating modes64-bit
ECC supported by processorNo
Thermal Design Power (TDP)65 W
Number of processors installed1
CPU multiplier (bus/core ratio)9
Number of Processing Die Transistors410 M
Audio systemHigh Definition Audio
Product typeWorkstation
Motherboard chipsetIntel® X38 Express
ECCYes
Internal memory2 GB
Memory clock speed800 MHz
Internal memory typeDDR2-SDRAM
Maximum internal memory8 GB
Memory layout (slots x size)2 x 1 GB
HDD speed7200 RPM
HDD capacity250 GB
HDD interfaceSATA
Optical drive typeDVD-RW
Graphics card-
Networking featuresGigabit Ethernet (10/100/1000)
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power supply475 W
Chassis typeTower
Country of originChina
Processor codeSLB9J
Processor ARK ID33910
Processor package size37.5 x 37.5 mm
On-board graphics card modelNot available
Weight and Dimensions IconWeight and Dimensions
Depth456 mm
Width168 mm
Height450 mm
Weight19000 g

Related product manuals