HP xw4600 User Manual

To launch the HPBR, slect Start>All Programs>HP Backup & Recovery>HP Backup and Recovery
Manager.
CAUTION: Before you attempt any operating system restore, backup your data . All data on the
Windows partition is deleted when you perform a system restore using the HPBR process. However,
the recovery partition on the system drive and other partitions will not be affected.
Creating system recovery DVDs or CDs
You can create a set of system recovery DVDs or CDs if you have a writable optical drive. After launching
the HP Backup and Restore Manager, you can create International Standards Organization (ISO)
images of the factory image, or write them directly to CD or DVD. You can also create a supplemental
HP Backup and Recovery Manager CD. (There may be additional CDs you can create depending on
the options purchased.) You can also move CD images to another location, such as a network share,
or to be copied to a DVD or CD at a later time or from another system.
Restoring from HPBR DVDs or CDs
To start the system recovery process, boot from the DVD or CD you created previously, then carefully
follow the online instructions.
Restoring a system directly from the recovery partition
Follow these steps to start the HPBR system restore process from the Recovery Manager:
1. Boot the workstation.
2. When prompted on the boot splash screen to enter the Recovery Manager, press F11.
3. Follow the prompts to restore the system to factory-like condition.
Reclaiming hard drive space from the recovery partition
To free up hard drive space, you can remove only the recovery partition, or you can completely uninstall
the HP Backup and Recovery Manager application.
CAUTION: If the recovery partition is removed:
– The F11 Emergency Recovery function becomes unavailable.
– The ability to recover the system is lost.
– Any recovery images contained in the recovery partition are deleted.
– The ability to create a recovery media set is lost.
CAUTION: If you uninstall the HP Backup and Recovery Manager application, emergency recovery
and data backup and recovery are no longer possible.
●
Removing only the recovery partition—The recovery partition can be removed by selecting
Remove HP Recovery Partition from the HP Backup and Recovery program folder. When the
HP Recovery Partition is removed, the recovery partition is deleted, the user partition is extended
to reclaim the unused hard drive space, and the F11 boot prompt is removed. The HP Backup and
Recovery Manager application remains and can be used for data backup and restore.
●
Uninstalling the HP Backup and Recovery Manager application—The HP Backup and
Recovery Manager application can be uninstalled using the Programs and Features utility under
ENWW Setting up Microsoft Windows Vista Business software 17

HP xw4600 Specifications

General

Tcase	72.4 °C
Bus type	FSB
Stepping	E0
Processor cache	6 MB
Processor cores	2
Processor model	E8400
System bus rate	- GT/s
Processor family	Intel® Core™2 Duo
Processor series	Intel Core 2 Duo E8000 Series
Processor socket	LGA 775 (Socket T)
Processor codename	Wolfdale
Processing Die size	107 mm²
Processor frequency	3 GHz
Processor cache type	L2
Processor lithography	45 nm
Processor manufacturer	Intel
Processor front side bus	1333 MHz
Processor operating modes	64-bit
ECC supported by processor	No
Thermal Design Power (TDP)	65 W
Number of processors installed	1
CPU multiplier (bus/core ratio)	9
Number of Processing Die Transistors	410 M
Audio system	High Definition Audio
Product type	Workstation
Motherboard chipset	Intel® X38 Express
ECC	Yes
Internal memory	2 GB
Memory clock speed	800 MHz
Internal memory type	DDR2-SDRAM
Maximum internal memory	8 GB
Memory layout (slots x size)	2 x 1 GB
HDD speed	7200 RPM
HDD capacity	250 GB
HDD interface	SATA
Optical drive type	DVD-RW
Graphics card	-
Networking features	Gigabit Ethernet (10/100/1000)
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power supply	475 W
Chassis type	Tower
Country of origin	China
Processor code	SLB9J
Processor ARK ID	33910
Processor package size	37.5 x 37.5 mm
On-board graphics card model	Not available

Weight and Dimensions

Depth	456 mm
Width	168 mm
Height	450 mm
Weight	19000 g