EasyManuals Logo

HP xw4600 User Manual

HP xw4600
176 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #150 background imageLoading...
Page #150 background image
Can recover from single drive failure
Improved read performance
RAID 1E
Three drives minimum
Can be an odd number of drives
Can always recover from a single drive failure and, in some cases, can recover from two drive
failures
SAS RAID 0 configuration
Follow the steps below to configure an Integrated Striped (IS) volume with the BIOS-based configuration
utility. The configuration procedure assumes that the system already has the required disk and disk
controllers.
1. On the Main menu screen of the BIOS-based configuration utility, use the arrow keys to select an
adapter.
2. Press Enter to go to the Adapter Properties screen.
3. On the Adapter Properties screen, use the arrow keys to select RAID Properties.
4. Press Enter to go to the RAID Properties screen.
5. In the RAID Properties screen, use the arrow keys to select the first disk for the IS volume. Then
use the arrow keys to move to the Array Disk column for this disk, and press the SPACE, +, or -
key to select Yes as the value for this column. If partitions are defined on the selected disk, a
message appears warning you that data on the disk will be lost when the striped volume is created.
Press the M key to migrate, or the D key to delete the data on the drive.
6. Repeat the previous step to select up to three more disks for the striped volume.
7. Press the C key to create the array once all drives have been chosen, then press Esc and
select Save.
SAS RAID 1 configuration
Follow the steps below to configure an Integrated Mirroring (IM) volume with the BIOS-based
configuration utility. The configuration procedure assumes that the system already has the required disk
and disk controllers.
1. On the Main menu screen of the BIOS-based configuration utility, use the arrow keys to select an
adapter.
2. Press Enter to go to the Adapter Properties screen.
3. On the Adapter Properties screen use the arrow keys to select RAID Properties.
4. Press Enter to go to the RAID Properties screen. .
5. Chose one of the following options:
142 Chapter 6 Configuring RAID devices ENWW

Table of Contents

Other manuals for HP xw4600

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP xw4600 and is the answer not in the manual?

HP xw4600 Specifications

General IconGeneral
Tcase72.4 °C
Bus typeFSB
SteppingE0
Processor cache6 MB
Processor cores2
Processor modelE8400
System bus rate- GT/s
Processor familyIntel® Core™2 Duo
Processor seriesIntel Core 2 Duo E8000 Series
Processor socketLGA 775 (Socket T)
Processor codenameWolfdale
Processing Die size107 mm²
Processor frequency3 GHz
Processor cache typeL2
Processor lithography45 nm
Processor manufacturerIntel
Processor front side bus1333 MHz
Processor operating modes64-bit
ECC supported by processorNo
Thermal Design Power (TDP)65 W
Number of processors installed1
CPU multiplier (bus/core ratio)9
Number of Processing Die Transistors410 M
Audio systemHigh Definition Audio
Product typeWorkstation
Motherboard chipsetIntel® X38 Express
ECCYes
Internal memory2 GB
Memory clock speed800 MHz
Internal memory typeDDR2-SDRAM
Maximum internal memory8 GB
Memory layout (slots x size)2 x 1 GB
HDD speed7200 RPM
HDD capacity250 GB
HDD interfaceSATA
Optical drive typeDVD-RW
Graphics card-
Networking featuresGigabit Ethernet (10/100/1000)
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power supply475 W
Chassis typeTower
Country of originChina
Processor codeSLB9J
Processor ARK ID33910
Processor package size37.5 x 37.5 mm
On-board graphics card modelNot available
Weight and Dimensions IconWeight and Dimensions
Depth456 mm
Width168 mm
Height450 mm
Weight19000 g

Related product manuals