Keithley 2001

4.8.8 SPE, SPD (serial polling) .......................................................................................................................... 4-27
4.9 Programming syntax.......................................................................................................................................... 4-29
4.10 Common commands.......................................................................................................................................... 4-35
4.10.1 *CLS  clear status.................................................................................................................................. 4-36
4.10.2 *ESE  event enable................................................................................................................................ 4-36
4.10.3 *ESE?  event enable query.................................................................................................................... 4-38
4.10.4 *ESR?  event status register query........................................................................................................ 4-38
4.10.5 *IDN?  identification query................................................................................................................... 4-40
4.10.6 *OPC  operation complete..................................................................................................................... 4-40
4.10.7 *OPC?  operation complete query......................................................................................................... 4-41
4.10.8 *OPT?  option identification query....................................................................................................... 4-42
4.10.9 *RCL  recall .......................................................................................................................................... 4-43
4.10.10 *RST  reset ............................................................................................................................................ 4-43
4.10.11 *SAV  save............................................................................................................................................ 4-43
4.10.12 *SRE  service request enable ................................................................................................................ 4-44
4.10.13 *SRE?  service request enable query..................................................................................................... 4-45
4.10.14 *STB?  status byte query....................................................................................................................... 4-46
4.10.15 *TRG  trigger ........................................................................................................................................ 4-47
4.10.16 *TST?  self-test query ........................................................................................................................... 4-48
4.10.17 *WAI  wait-to-continue......................................................................................................................... 4-48
4.11 Signal oriented measurement commands.......................................................................................................... 4-51
4.12 SCPI command subsystems............................................................................................................................... 4-57
4.13 Calculate subsystems......................................................................................................................................... 4-59
4.13.1 :CALCulate[1]............................................................................................................................................4-60
4.13.2 :CALCulate2.............................................................................................................................................. 4-65
4.13.3 :CALCulate3.............................................................................................................................................. 4-68
4.14 :CALibration subsystem.................................................................................................................................... 4-77
4.15 :DISPlay subsystem........................................................................................................................................... 4-79
4.16 :FORMat subsystem.......................................................................................................................................... 4-85
4.17 :OUTput subsystem........................................................................................................................................... 4-92
4.18 :ROUTe subsystem............................................................................................................................................ 4-94
4.18.1 :CLOSe <list>............................................................................................................................................ 4-95
4.18.2 :OPEN <list>............................................................................................................................................. 4-96
4.18.3 :OPEN:ALL............................................................................................................................................... 4-97
4.18.4 :SCAN commands..................................................................................................................................... 4-98
4.19 Sense subsystems............................................................................................................................................. 4-107
4.19.1 [:SENse[1]] subsystem............................................................................................................................ 4-115
4.19.2 :ALTernate[1] commands ....................................................................................................................... 4-116
4.19.3 :FUNCtion <name>................................................................................................................................. 4-116
4.19.4 DATA commands.................................................................................................................................... 4-117
4.19.5 :APERture <n>........................................................................................................................................ 4-118
4.19.6 :NPLCycles <n>...................................................................................................................................... 4-123
4.19.7 :COUPling AC|DC .................................................................................................................................. 4-127
4.19.8 RANGe commands.................................................................................................................................. 4-128
4.19.9 :REFerence <n>....................................................................................................................................... 4-133
4.19.10 :DIGits <n>.............................................................................................................................................. 4-137
4.19.11 :AVERage commands ............................................................................................................................. 4-141
4.19.12 :Filter ....................................................................................................................................................... 4-148
4.19.13 :DETector commands.............................................................................................................................. 4-149
4.19.14 :PWINdow <n> ....................................................................................................................................... 4-150
4.19.15 :METHod <name> .................................................................................................................................. 4-151
4.19.16 :SOURce <name>.................................................................................................................................... 4-151
4.19.17 THReshold commands ............................................................................................................................ 4-152
4.19.18 :TRANsducer <name> ............................................................................................................................ 4-155
iv