Keithley 2001 User Manual

General Information
1-3
Model 4288-1 Single Fixed Rack Mount Kit — Mounts a
single Model 2001 in a standard 19-inch rack.
Model 4288-2 Side-by-side Rack Mount Kit — Mounts
two instruments (Models 182, 428, 486, 487, 2001, 7001)
side-by-side in a standard 19-inch rack.
Model 4288-3 Side-by-side Rack Mount Kit — Mounts a
Model 2001 and a Model 199 side-by-side in a standard 19-
inch rack.
Model 4288-4 Side-by-side Rack Mount Kit — Mounts a
Model 2001 and a 5-inch instrument (Models 195A, 196,
220, 224, 230, 263, 595, 614, 617, 705, 740, 775, etc.) side-
by-side in a standard 19-inch rack.
Models 7007-1 and 7007-2 Shielded IEEE-488 Cables —
Connect the Model 2001 to the IEEE-488 bus using shielded
cables and connectors to reduce electromagnetic interference
(EMI). The Model 7007-1 is one meter long; the Model
7007-2 is two meters long.
Models 8501-1 and 8501-2 Trigger Link Cables — Con-
nect the Model 2001 to other instruments with Trigger Link
connectors (e.g., Model 7001 Switch System). The Model
8501-1 is one meter long; the Model 8501-2 is two meters
long.
Model 8502 Trigger Link Adapter — Allows you to con-
nect the Trigger Link of the Model 2001 to instruments that
use the standard BNC (In/Out) external triggering technique.
Model 8530 IEEE-488 to Centronics Printer Adapter Ca-
ble — Translates the IEEE-488 connector pinout and signal
level to a Centronics termination. This permits a standard
Centronics parallel printer to be connected to a Model 2001
in TALK-ONLY mode.
Model 8605 High Performance Modular Test Leads —
Consists of two high voltage (1000V) test probes and leads.
The test leads are terminated with a banana plug with retract-
able sheath on each end. (Each Model 2001 is shipped with
one set of these test leads.)
Model 8606 High Performance Probe Tip Kit — Consists
of two spade lugs, two alligator clips, and two spring hook
test probes. (The spade lugs and alligator clips are rated at
30V RMS, 42.4V peak; the test probes are rated at 1000V.)
These components are designed to be used with high perfor-
mance test leads terminated with banana plugs, such as the
Model 8605 High Performance Modular Test Leads.
The following test leads and probes are rated at 30V RMS,
42.4V peak:
Models 5805 and 5805-12 Kelvin Probes — Consists of
two spring-loaded Kelvin test probes with banana plug ter-
mination. Designed to be used with instruments that measure
4-terminal resistance. The Model 5805 is 0.9m long; the
Model 5805-12 is 3.6m long.
Model 5806 Kelvin Clip Lead Set — Includes two Kelvin
clip test leads (0.9m) with banana plug termination. De-
signed for instruments that measure 4-terminal resistance. A
set of eight replacement rubber bands for the Model 5806 is
available as Keithley P/N GA-22.
Model 8604 SMD Probe Set — Consists of two test leads
(3ft), each terminated with a surface mount device “grabber”
clip on one end and a banana plug with retractable sheath on
the other end.
Model 8610 Low Thermal Shorting Plug — Consists of
four banana plugs mounted to a 1-inch square circuit board,
interconnected to provide a short circuit among all plugs.
Model 8611 Low Thermal Patch Leads — Consists of two
test leads (3ft), each with a banana plug with a retractable
sheath at each end. These leads minimize the thermally-
induced offsets that can be created by test leads.
Model 8612 Low Thermal Spade Leads — Consists of two
test leads (3ft), each terminated with a spade lug on one end
and a banana plug with a retractable sheath on the other end.
These leads minimize the thermally-induced offsets that can
be created by test leads.
Model 8680 RTD Probe Adapter — This adapts RTDs with
terminated and unterminated cables to instruments with ba-
nana jacks for measuring 4-terminal resistance. It has a 4-pin
“T”-style connector and a 4-pin screw terminal block.
Model 8681 Miniature RTD Surface Probe — This is a low
cost platinum 4-wire-RTD with unterminated wires. It is de-
signed to measure the temperature of flat surfaces or free
space.
Model 8693 General Purpose/Immersion RTD Probe —
This probe has a platinum RTD sensor. It is designed for im-
mersion in liquids as well as other general purpose applica-
tions.
Model 8695 Surface RTD Probe — This probe has a plati-
num RTD sensor. It is designed to measure the temperature
of flat surfaces of solids.
Model 8696 Air/Gas RTD Probe — This probe has a plati-
num RTD sensor. It has an exposed junction within a protec-
tive shroud for measuring the temperature of air or gases.

Keithley 2001 Specifications

General

Model	2001
Category	Multimeter
Manufacturer	Keithley
Type	Digital Multimeter
Digits of Resolution	7.5
DC Voltage Range	100 mV to 1000 V
AC Voltage Range	100 mV to 750 V
Frequency Range	3 Hz to 500 kHz
Connectivity	GPIB, RS-232
Display	VFD
Resistance Accuracy	0.008% + 2.0 mΩ
Frequency Accuracy	±0.01%
DC Current Range	10 μA to 3 A
AC Current Range	10 μA to 3 A
Power Supply	100 V to 240 V AC, 45 Hz to 66 Hz