Lenze i410 - Page 261

Display code Short designaon Default seng Seng range Address Category
└ P708.03 Mode Keyp.control o [0] Selecon list 0x2602:003 general
P710.xx Load loss detect
└ P710.01 Threshold 0.0 % 0.0 ... 200.0 % 0x4006:001 general
└ P710.02 Delay
me 0.0 s 0.0 ... 300.0 s 0x4006:002 general
└ P710.03 Error response No response [0] Selecon list 0x4006:003 general
P712.xx Brake control
└ P712.01 Brake mode O [2] Selecon list 0x2820:001 general
└ P712.02 Closing me 100 ms 0 ... 10000 ms 0x2820:002 general
└ P712.03 Opening me 100 ms 0 ... 10000 ms 0x2820:003 general
└ P712.07 Closing thresh. 0.2 Hz 0.0 ... 599.0 Hz 0x2820:007 general
└ P712.08 Holding load 0.0 % -500.0 ... 500.0 % 0x2820:008 general
└ P712.12 ClosingThr delay 0 ms 0 ... 10000 ms 0x2820:012 general
└ P712.13 HoldLoad rampm 0 ms 0 ... 100 ms 0x2820:013 general
└ P712.15 Brake status - - (Read only) 0x2820:015 general
P718.xx Flying restart
└ P718.01 Current 30 % 0 ... 100 % 0x2BA1:001 MCTRL
└ P718.02 Start frequency 20.0 Hz -599.0 ... 599.0 Hz 0x2BA1:002 MCTRL
└ P718.03 Restart me 5911 ms * 1 ... 60000 ms 0x2BA1:003 MCTRL
└ P718.08 Fl.res.frequency x.x Hz - (Read only) 0x2BA1:008 MCTRL
P732.00 Auto-Save EPM Inhibit [0] Selecon list 0x2829 general
P740.xx Favorites se.
└ P740.01 Parameter 1 0x2DDD0000 0x00000000 ... 0xFFFFFF00 0x261C:001 general
└ P740.02 Parameter 2 0x60780000 0x00000000 ... 0xFFFFFF00 0x261C:002 general
└ P740.03 Parameter 3 0x2D890000 0x00000000 ... 0xFFFFFF00 0x261C:003 general
└ P740.04 Parameter 4 0x603F0000 0x00000000 ... 0xFFFFFF00 0x261C:004 general
└ P740.05 Parameter 5 0x28240000 0x00000000 ... 0xFFFFFF00 0x261C:005 general
└ P740.06 Parameter 6 0x28600100 0x00000000 ... 0xFFFFFF00 0x261C:006 general
└ P740.07 Parameter 7 0x28380100 0x00000000 ... 0xFFFFFF00 0x261C:007 general
└ P740.08 Parameter 8 0x28380300 0x00000000 ... 0xFFFFFF00 0x261C:008 general
└ P740.09 Parameter 9 0x25400100 0x00000000 ... 0xFFFFFF00 0x261C:009 general
└ P740.10 Parameter 10 0x29150000 0x00000000 ... 0xFFFFFF00 0x261C:010 general
└ P740.11 Parameter 11 0x29160000 0x00000000 ... 0xFFFFFF00 0x261C:011 general
└ P740.12 Parameter 12 0x29170000 0x00000000 ... 0xFFFFFF00 0x261C:012 general
└ P740.13 Parameter 13 0x29180000 0x00000000 ... 0xFFFFFF00 0x261C:013 general
└ P740.14 Parameter 14 0x2C000000 0x00000000 ... 0xFFFFFF00 0x261C:014 general
└ P740.15 Parameter 15 0x2B000000 0x00000000 ... 0xFFFFFF00 0x261C:015 general
└ P740.16 Parameter 16 0x2B010100 0x00000000 ... 0xFFFFFF00 0x261C:016 general
└ P740.17 Parameter 17 0x2B010200 0x00000000 ... 0xFFFFFF00 0x261C:017 general
└ P740.18 Parameter 18 0x283A0000 0x00000000 ... 0xFFFFFF00 0x261C:018 general
└ P740.19 Parameter 19 0x29390000 0x00000000 ... 0xFFFFFF00 0x261C:019 general
└ P740.20 Parameter 20 0x2D430100 0x00000000 ... 0xFFFFFF00 0x261C:020 general
└ P740.21 Parameter 21 0x2D4B0100 0x00000000 ... 0xFFFFFF00 0x261C:021 general
└ P740.22 Parameter 22 0x2B120100 0x00000000 ... 0xFFFFFF00 0x261C:022 general
└ P740.23 Parameter 23 0x60750000 0x00000000 ... 0xFFFFFF00 0x261C:023 general
└ P740.24 Parameter 24 0x60730000 0x00000000 ... 0xFFFFFF00 0x261C:024 general
└ P740.25 Parameter 25 0x26310100 0x00000000 ... 0xFFFFFF00 0x261C:025 general
└ P740.26 Parameter 26 0x26310200 0x00000000 ... 0xFFFFFF00 0x261C:026 general
└ P740.27 Parameter 27 0x26310300 0x00000000 ... 0xFFFFFF00 0x261C:027 general
└ P740.28 Parameter 28 0x26310400 0x00000000 ... 0xFFFFFF00 0x261C:028 general
└ P740.29 Parameter 29 0x26310500 0x00000000 ... 0xFFFFFF00 0x261C:029 general
└ P740.30 Parameter 30 0x26310600 0x00000000 ... 0xFFFFFF00 0x261C:030 general
└ P740.31 Parameter 31 0x26310700 0x00000000 ... 0xFFFFFF00 0x261C:031 general
└ P740.32 Parameter 32 0x26310800 0x00000000 ... 0xFFFFFF00 0x261C:032 general
└ P740.33 Parameter 33 0x26310900 0x00000000 ... 0xFFFFFF00 0x261C:033 general
* Default seng dependent on the model.
Using accessories
K
eypad
Keypad parameterisaon mode
261