Lenze i410 - Page 314

Address Name Default seng Category Data type Factor A M
0x2540:003
(P208.03)
Mains sengs: Undervoltage error threshold x V (Read only) general U16 1 - -
0x2540:004
(P208.04)
Mains sengs: Undervoltage reset threshold x V (Read only) general U16 1 - -
0x2540:005
(P208.05)
Mains sengs: Overvoltage warning threshold 0 V * general U16 1 P -
0x2540:006
(P208.06)
Mains sengs: Overvoltage error threshold x V (Read only) general U16 1 - -
0x2540:007
(P208.07)
Mains sengs: Overvoltage reset threshold x V (Read only) general U16 1 - -
0x2541:001
(P706.01)
Brake energy management: Operang mode Ramp
funcon generator
stop (RFGS) [1]
general U8 1 P -
0x2541:002
(P706.02)
Brake energy management: Acve threshold x V (Read only) general U16 1 P -
0x2541:003
(P706.03)
Brake energy management: Reduced threshold 0 V general U16 1 P -
0x2541:004
(P706.04)
Brake energy management: Addional frequency 0.0 Hz general U16 10 P -
0x2541:005
(P706.05)
Brake energy management: Deceleraon override
me
2.0 s general U16 10 P -
0x2601:001
(P202.01)
Keypad setpoints: Frequency setpoint 20.0 Hz general U16 10 P r
0x2601:002
(P202.02)
Keypad setpoints: Process controller setpoint 0.00 PID unit general I16 100 P r
0x2601:003
(P202.03)
Keypad setpoints: Torque setpoint 100.0 % general I16 10 P r
0x2602:001
(P708.01)
Manual control: Keypad seng CTRL & F/R enable [1] general U8 1 P -
0x2602:002
(P708.02)
Manual control: Keypad rotaonal direcon Forward [0] general U8 1 P -
0x2602:003
(P708.03)
Manual control: Mode Keypad full control o [0] general U8 1 - -
0x261C:001
(P740.01)
Favorites
sengs: Parameter 1 0x2DDD0000 general IDX 1 PH -
0x261C:002
(P740.02)
Favorites sengs: Parameter 2 0x60780000 general IDX 1 PH -
0x261C:003
(P740.03)
Favorites sengs: Parameter 3 0x2D890000 general IDX 1 PH -
0x261C:004
(P740.04)
Favorites sengs: Parameter 4 0x603F0000 general IDX 1 PH -
0x261C:005
(P740.05)
Favorites sengs: Parameter 5 0x28240000 general IDX 1 PH -
0x261C:006
(P740.06)
Favorites
sengs: Parameter 6 0x28600100 general IDX 1 PH -
0x261C:007
(P740.07)
Favorites sengs: Parameter 7 0x28380100 general IDX 1 PH -
0x261C:008
(P740.08)
Favorites sengs: Parameter 8 0x28380300 general IDX 1 PH -
0x261C:009
(P740.09)
Favorites sengs: Parameter 9 0x25400100 general IDX 1 PH -
0x261C:010
(P740.10)
Favorites sengs: Parameter 10 0x29150000 general IDX 1 PH -
0x261C:011
(P740.11)
Favorites sengs: Parameter 11 0x29160000 general IDX 1 PH -
0x261C:012
(P740.12)
Favorites sengs: Parameter 12 0x29170000 general IDX 1 PH -
0x261C:013
(P740.13)
Favorites sengs: Parameter 13 0x29180000 general IDX 1 PH -
* Default seng dependent on the model.
Appendix
P
arameter aribute list
314