Metcom Solutions MCS301 User Manual

MCS301 - 3ph meter Page 81 of 142
MCS301 meter - product Manual 1.25 MetCom Solutions GmbH
101 Comms ok M-Bus channel 1 Comms with M-Bus meter connected to channel 1 of the M-Bus is ok again.
102
Replace Battery M
-
Bus channel 1
B
attery must be exchanged due to the expected end of
life time.
103
Fraud attempt M
-
Bus channel 1
F
raud attempt has been registered.
104
Clock adjusted M
-
Bus channel 1
C
lock has been adjusted.
105
New M
-
Bus device installed
channel 1
T
he meter (M
-
Bus master) has registered a M
-
Bus device connected to cha
nnel 1
with a new serial number
106 Permanent Error M-Bus channel 1 Severe error reported by M-Bus device
107 LPCAP_M4 disabled Capturing of M-Bus profile 4 is disabled
110
Comm
s
error M
-
bus channel 2
C
omm
s
problem when reading the meter connected to ch
annel 2 of the M
-
Bus
111
Comm
s
ok M
-
bus channel 2
C
omm
s
with M
-
Bus meter connected to channel 2
of the M
-
Bus is ok again.
112
Replace Battery M
-
Bus channel 2
T
he battery must be exchanged due to the expected end of life time.
113
Fraud attempt M
-
Bus cha
nnel 2
F
raud attempt has been registered in the M
-
Bus device.
114
Clock adjusted M
-
Bus channel 2
C
lock has been adjusted.
115
New M
-
Bus device installed
channel 2
The
meter (M
-
Bus master) has registered a M
-
Bus device connected to channel 2
with a new serial number
116
Permanent Error M
-
Bus channel 2
Severe error reported by M-Bus device (Bit 3 in MBUS status EN13757)
120 Comms error M-bus channel 3 Comms problem when reading the meter connected to channel 3 of the M-Bus
121 Comms ok M-bus channel 3 Comms with M-Bus meter connected to channel 3 of the M-Bus is ok again
122 Replace Battery M-Bus channel 3 The battery must be exchanged due to the expected end of life time.
123 Fraud attempt M-Bus channel 3 Fraud attempt has been registered.
124
Clock a
djusted M
-
Bus channel 3
C
lock has been adjusted.
125
New M
-
Bus device installed
channel 3
The
meter (M
-
Bus master) has registered a M
-
Bus device connected to channel 3
with a new serial number
126 Permanent Error M-Bus channel 3 Severe error reported by M-Bus device (Bit 3 in MBUS status EN13757)
128 M-Bus FW verification failed M-Bus channel x the FW verification failed
130
Comm
s
error M
-
bus channel 4
C
omm
s
problem when reading the meter connected to channel 4 of the M
-
Bus
131
Comm
s
ok M
-
bus channel 4
I
C
comm
s
with M
-
Bus meter connected to channel 4
of the M
-
Bus is ok again
132
Replace Battery M
-
Bus channel 4
T
he battery must be exchanged due to the expected end of life time.
133 Fraud attempt M-Bus channel 4 Fraud attempt has been registered.
134 Clock adjusted M-Bus channel 4 The clock has been adjusted.
135
New M
-
Bus device installed
channel 4
T
he meter (M
-
Bus master) has registered a M
-
Bus device connected to channel 4
with a new serial number
136
Permanent Error M
-
Bus channel 4
Severe error rep
orted by M
-
Bus device (Bit 3 in MBUS status EN13757)
254
Load profile cleared
Any of the profiles cleared.
NOTE: If it appears in Standard Event Log then any of the E-load profiles was
cleared. If the event appears in the M-Bus Event log then one of the M-Bus load
profiles was cleared
1 – Monthly
2 – LP1 (hourly)
3 – LP2 (daily)
4 - Supervision Average
5 - Supervision Minimum
6 - Supervision Maximum
7 - Supervision Harmonics
8 - LP Mbus1
9 - LP Mbus2
10 – LP Mbus 3
11 – LP Mbus 4
255
Event log cleared
T
he event log was cleared. This is always the first entry in an event log.
It is
only
stored in the affected event log.
Table 43: Definition of log file 8 – M-Bus Event Log

Metcom Solutions MCS301 Specifications

General

Brand	Metcom Solutions
Model	MCS301
Category	Measuring Instruments
Language	English