Omron SYSDRIVE 3G3MV SERIES User Manual

5-26
• If acceleration/deceleration time selection 2 (setting: 27) is not set at any multi-function input from
n050 to n056, the Inverter will determine that the acceleration/deceleration selection 2 is set to OFF,
and select the acceleration/deceleration time.
In the same way, if acceleration/deceleration time selection 1 (setting: 11) is not set at any multi-func-
tion input, the Inverter will determine that the acceleration/deceleration selection 1 is set to OFF, and
select the acceleration/deceleration time.
• Deceleration time 2 is used if emergency stop (setting: 19 to 22) is set at any multi-function input from
n050 to n056 and if decelerate to a stop (setting: 0) is set at stopping mode selection n005.
n019
Acceleration Time 1 Register 0113 Hex Changes during
operation
Yes
Setting
range
0.0 to 6,000 (s) (See note 1.) Unit of
setting
0.1 s
(See note
1.)
Default setting 10.0
n020
Deceleration Time 1 Register 0114 Hex Changes during
operation
Yes
Setting
range
0.0 to 6,000 (s) (See note 1.) Unit of
setting
0.1 s
(See note
1.)
Default setting 10.0
n021
Acceleration Time 2 Register 0115 Hex Changes during
operation
Yes
Setting
range
0.0 to 6,000 (s) (See note 1.) Unit of
setting
0.1 s
(See note
1.)
Default setting 10.0
n022
Deceleration Time 2 Register 0116 Hex Changes during
operation
Yes
Setting
range
0.0 to 6,000 (s) (See note 1.) Unit of
setting
0.1 s
(See note
1.)
Default setting 10.0
n041
Acceleration Time 3 Register 0129 Hex Changes during
operation
Yes
Setting
range
0.0 to 6,000 (s) (See note 1.) Unit of
setting
0.1 s
(See note
1.)
Default setting 10.0
n042
Deceleration Time 3 Register 012A Hex Changes during
operation
Yes
Setting
range
0.0 to 6,000 (s) (See note 1.) Unit of
setting
0.1 s
(See note
1.)
Default setting 10.0
n043
Acceleration Time 4 Register 012B Hex Changes during
operation
Yes
Setting
range
0.0 to 6,000 (s) (See note 1.) Unit of
setting
0.1 s
(See note
1.)
Default setting 10.0
n044
Deceleration Time 4 Register 012C Hex Changes during
operation
Yes
Setting
range
0.0 to 6,000 (s) (See note 1.) Unit of
setting
0.1 s
(See note
1.)
Default setting 10.0
Basic Operation
Chapter 5

Omron SYSDRIVE 3G3MV SERIES Specifications

General

Model	SYSDRIVE 3G3MV SERIES
Category	Inverter
Input Frequency	50/60 Hz
Output Frequency	0.1 to 400 Hz
Cooling Method	Forced Air Cooling
Input Voltage	200 to 240 VAC, 380 to 480 VAC
Horsepower Range	0.1 to 15 HP
Power Range	0.1 to 11 kW
Overload Capacity	150% for 60 seconds
Braking Unit	Built-in
Protection Functions	Overcurrent, Overvoltage, Undervoltage, Overheat
Communication	RS-485
Ambient Temperature	-10 to 50°C
Storage Temperature	-20 to 65°C
Humidity	5 to 95% RH (non-condensing)
Vibration	5.9 m/s² or less
Voltage Class	200V, 400V