Omron V1000 - Page 403

L4-01 .................................................................... 257, 323
L4-02 .................................................................... 257, 323
L4-03 .......................................................................... 323
L4-04 .......................................................................... 323
L4-05 .......................................................................... 323
L4-06 .......................................................................... 323
L4 Frequency Detection .................................................... 323
L5-01 .................................................................... 245, 323
L5-02 .......................................................................... 323
L5-04 .......................................................................... 323
L5-05 .......................................................................... 323
L5 Fault Reset................................................................ 323
L6-01 .......................................................................... 324
L6-02 ........................................................ 236, 239, 244, 324
L6-02 and L6-03 ....................................................... 239, 246
L6-03 ........................................................ 236, 239, 244, 324
L6-04 .......................................................................... 324
L6-05 ........................................................ 236, 239, 244, 324
L6-05 and L6-06 ................................................. 239, 244, 246
L6-06 ........................................................ 236, 239, 244, 324
L6-08 .......................................................................... 325
L6-09 .......................................................................... 325
L6-10 .......................................................................... 325
L6-11 .......................................................................... 325
L6 Overtorque Detection ................................................... 324
L7-01 .................................................................... 251, 325
L7-01 through L3-04 ........................................................ 226
L7-01 through L7-04 ...................................... 230, 254, 255, 256
L7-02 .................................................................... 251, 325
L7-03 .......................................................................... 325
L7-04 .......................................................................... 325
L7-06 .......................................................................... 325
L7-07 .......................................................................... 325
L7 Torque Limit ............................................................. 325
L8: Hardware Protection.................................................... 325
L8-01 ................................................................59, 238, 325
L8-02 .......................................................................... 235
L8-03 .......................................................................... 325
L8-05 .......................................................................... 238
L8-07 .......................................................................... 233
L8-09 .................................................................... 233, 326
L8-10 .......................................................................... 326
L8-11 .......................................................................... 326
L8-12 .................................................................... 295, 326
L8-15 .......................................................................... 326
L8-18 .......................................................................... 326
L8-19 .......................................................................... 326
L8-29 .................................................................... 295, 326
L8-38 .................................................................... 258, 326
L8-41 .......................................................................... 326
LED Check ................................................................... 335
LED Operator .........................................................22, 66, 67
LF ........................................................................ 228, 233
LF2 ...................................................................... 228, 233
Line-to-Line Motor Resistance Online Tuning .......................... 328
Line-to-Line Resistance Auto-Tuning .................................... 254
Line-to-Line Resistance Error........................................ 229, 250
LO/RE..................................................................67, 74, 92
Load Current ................................................................. 328
Load Falls When Brake is Applied ....................................... 257
Load Inertia................................................................... 328
Load Inertia for PM ......................................................... 239
Load Inertia Ratio
...................................................... 237, 323
LOCAL..........................................................................74
LOCAL/REMOTE Key Function Selection ............................. 329
Local/Remote Run Selection............................................... 300
Local/Remote Selection..................................................... 315
Loss of Reference............................................................ 317
Low Voltage Directive...................................................... 382
L Protection Function ....................................................... 321
M
Magnetic Flux Compensation Capacity .................................. 300
Magnetic Flux Compensation Value ...................................... 300
Main Circuit Connection Diagram ..................................... 42, 49
Main Circuit Terminal Functions............................................46
Main Circuit Terminal Power Supply.......................................48
Main Circuit Terminals Connection.........................................42
Main Circuit Terminal Wiring .........................................25, 388
Main Frequency Reference ...................................................57
Main Frequency Reference Input............................................51
Main Power Circuit Voltage Adjustment Gain .......................... 322
Maintenance .................................................................. 266
Master Speed Reference Lower Limit .................................... 307
Maximum Applicable Motor Capacity (kW) ............................ 291
Maximum Motor Size Allowed (kW)......................... 289, 290, 291
Mechanical Weakening (N.O.)............................................. 318
Mechanical Weakening Detection 1 ................................ 228, 244
Mechanical Weakening Detection Operation ............................ 325
Mechanical Weakening Detection Speed Level ......................... 325
Mechanical Weakening Detection Start Time ........................... 325
Mechanical Weakening Detection Time.................................. 325
MEMOBUS/Modbus Communication Error........... 227, 228, 230, 241
MEMOBUS/Modbus Communications Reference...................... 336
MEMOBUS/Modbus Communications Test Mode Complete ........ 245
MEMOBUS/Modbus Communications Test Mode Error.............. 245
MEMOBUS/Modbus Error Code ......................................... 334
MEMOBUS/Modbus Switch Settings ......................................58
MEMOBUS/Modbus Termination ..........................................25
MEMOBUS/Modbus Test Mode Complete.............................. 228
Mid Output Voltage A ................................................ 224, 225
Minimum Output Frequency ............................................... 259
Minimum Output Voltage ............................................ 224, 225
Minor Alarms ................................................................ 227
Minor Fault ................................................................... 250
Minor Faults .................................................................. 227
Modes ...........................................................................70
Momentary Power Loss Minimum Baseblock Time.................... 321
Momentary Power Loss Operation Selection ............................ 321
Momentary Power Loss Ride-Thru Time ................................ 321
Momentary Power Loss Voltage Recovery Ramp Time ............... 321
Monitor Output.................................................................51
Most Recent Fault ........................................................... 334
Motor 2 Iron-Core Saturation Coefficient 3.............................. 310
Motor 2 Iron Loss............................................................ 310
Motor 2 Leakage Inductance ............................................... 310
Motor 2 Line-to-Line Resistance .......................................... 310
Motor 2 Mechanical Loss................................................... 310
Motor 2 Motor Iron-Core Saturation Coefficient 1 ..................... 310
Motor 2 Motor Iron-Core Saturation Coefficient 2 ..................... 310
Motor 2 Motor Poles ........................................................ 310
Motor 2 Rated Capacity..................................................... 310
Motor 2 Rated Current ...................................................... 310
Motor 2 Rated No-Load Current........................................... 310
Motor 2 Rated Slip .......................................................... 310
Index
402
SIEP C710606 20 OYMC AC Drive - V1000 User Manual
7/16/2008-13:23