Siemens SINAMICS G130 - Page 592

Appendix
A.2 Parameter macros
Inverter chassis units
592 Operating Instructions, 07/2016, A5E00331449A
Sink
Source
Parameters
Description
DO
Parameters
Description
DO
p1240
Vdc controller configuration
Vector
1
Vdc-max controller enabled
Vector
p1254 Vdc controller automatic ON level
detection
Vector 1 Automatic detection enabled Vector
p1280
Vdc controller configuration (V/f)
Vector
1
Vdc-max controller enabled
Vector
p1300 Open-loop/closed-loop control
operating mode
Vector 20 Encoderless speed control Vector
p1911
Number of phases to be identified
Vector
1
1 phase
Vector
p2051[0]
CI: PROFIBUS PZD send word
Vector
r2089[0]
ZSW1
Vector
p2051[1]
CI: PROFIBUS PZD send word
Vector
r0063[0]
n-act unsmoothed
Vector
p2051[2]
CI: PROFIBUS PZD send word
Vector
r0068[0]
I-act unsmoothed
Vector
p2051[3]
CI: PROFIBUS PZD send word
Vector
r0080[0]
M-act unsmoothed
Vector
p2051[4]
CI: PROFIBUS PZD send word
Vector
r0082[0]
P-act unsmoothed
Vector
p2051[5]
CI: PROFIBUS PZD send word
Vector
r2131
FAULT
Vector
p2080[0]
BI: PROFIBUS send status word 1
Vector
r0899.0
Ready for switching on
Vector
p2080[1]
BI: PROFIBUS send status word 1
Vector
r0899.1
Ready for operation
Vector
p2080[2]
BI: PROFIBUS send status word 1
Vector
r0899.2
Operation
Vector
p2080[3]
BI: PROFIBUS send status word 1
Vector
r2139.3
Fault
Vector
p2080[4]
BI: PROFIBUS send status word 1
Vector
r0899.4
No OFF2
Vector
p2080[5]
BI: PROFIBUS send status word 1
Vector
r0899.5
No OFF3
Vector
p2080[6]
BI: PROFIBUS send status word 1
Vector
r0899.6
Switching on inhibited
Vector
p2080[7]
BI: PROFIBUS send status word 1
Vector
r2139.7
Alarm active
Vector
p2080[8]
BI: PROFIBUS send status word 1
Vector
r2197.7
No setpoint/actual value deviation
Vector
p2080[9]
BI: PROFIBUS send status word 1
Vector
r0899.9
Control request
Vector
p2080[10] BI: PROFIBUS send status word 1 Vector r2199.1 Comparison value reached Vector
p2080[11]
BI: PROFIBUS send status word 1
Vector
r1407.7
M/I/P limiting not active
Vector
p2080[12]
BI: PROFIBUS send status word 1
Vector
0
Vector
p2080[13] BI: PROFIBUS send status word 1 Vector r2129.14 No alarm for motor overtempera-
ture
Vector
p2080[14]
BI: PROFIBUS send status word 1
Vector
r2197.3
Clockwise
Vector
p2080[15] BI: PROFIBUS send status word 1 Vector r2129.15 No Therm. alarm Power unit
overload
Vector
p2088
PROFIBUS Invert status word
Vector
B800h
Vector
p2128[14] Select fault/alarm code for trigger Vector 7910 A7910: Alarm, motor overtemper-
ature
Vector
p2128[15] Select fault/alarm code for trigger Vector 5000 A5000: Therm. alarm Power unit
overload
Vector
p2153 Time constant revolutions actual
value filter
Vector 20 20 ms Vector
p4053[0] TM31 analog inputs, smoothing
time constant
TM31 0 0 ms TM31
p4056[0]
Type of analog inputs
TM31
0
Voltage 0...10 V
TM31
p4056[1]
Type of analog inputs
TM31
0
Voltage 0...10 V
TM31
p4076[0] Type of analog outputs TM31 1 Voltage 0...10 V TM31