YOKOGAWA UT55A User Manual

8-12
IM 05P01C31-01EN
n
CascadePrimary-loopControlFunctionBlockDiagram
Target setpoints 1 to 8
COM
Aux. input
*1
Output limiter
Manual operation
Manual preset output
Input error preset output
Preset output
Output tracking input
Output tracking switch (Tracking at ON)
AUTO (ON)/MAN (OFF) switch
STOP (ON)/RUN (OFF) switch
LOCALREMOTE
AUTO
When sensor
burnout occurs
Normal
MAN
ONOFF
RUN
STOP
SP ramp rate
SP limiter
PV input
Output tracking input
(from Loop-2 controller)
DI16PV RSP
Input type
Input unit
Input range/scale
Analog input bias
Square root extraction
Analog input filter
Input type
Input unit
Input range/scale
Analog input bias
Square root extraction
Analog input filter
Remote input filter
PV input bias
PV input filter
Ratio bias computation
Contact inputs
Output limiter
Output limiter
A.BS
A.FL
10-seg. linearizer approx./bias
BS
FL
CNT ALG
UPR, DNR TMU
SPNO SP
R/L
RMS
SPH, SPL
RFL
A.SR A.LC
UNIT
IN
RH, RL SDP SH, SL
A.BS
A.FL
A.SR A.LC
UNIT
IN
RH, RL SDP SH, SL
EPO
OH, OL
OH, OL OLMT
OH, OL
PO
S/R
MPON
Equipped as standard
Equipped as standard Equipped as standard
Heater break alarm
HAL2HAL1
Heater break
alarm 1
Heater break
alarm 2
Current
(to Loop-2 controller)
LPS
24 V loop
power supply
Current
OUT RET AL3AL2AL1
PMD
OU.H OU.L
An, Bn
Split computation
10-seg. linearizer approx./bias
RET.H RET.L
PMD An, Bn
Split computation
10-seg. linearizer approx./bias
RET retransmission output
RTS
Alarm
DI3DI2DI1
A/M
Control computation
(from Loop-2 controller)
PMD An, Bn
10-seg. linearizer approx./bias
PMD An, Bn
10-seg. linearizer approx./bias
PMD An, Bn
AIN2
Input type
Input unit
Input range/scale
Analog input bias
Square root extraction
Analog input filter
A.BS
A.FL
A.SR A.LC
UNIT
IN
RH, RL SDP SH, SL
10-seg. linearizer approx./bias
PMD An, Bn
No function
is assigned
to DI3.
Terminal Parameter Function
Analog signal Contact signal Front panel key
Legend
Alarm 1
(PV high limit)
Alarm 2
(PV low limit)
FAIL
(to Loop-2 controller)
PV display SP display
Input ladder calculation program (signal goes to the control computation as is when without ladder program). For ladder program, see the LL50A Parameter Setting Software User’s Manual.
Output ladder calculation program (signal goes to the output as is when without ladder program). For ladder program, see the LL50A Parameter Setting Software User’s Manual.
Aux. analog (remote) input
Communication
*1: RS-485, Ethernet, PROFIBUS-DP,
DeviceNet, CC-Link
(For Detailed model)
Remote input can be used when UT55A
optional suffix code /A2.
(For Standard model)
Remote input can be used when UT55A
suffix code: Type 2 = 7.
(For Detailed model)
UT55A/UT52A optional suffix code /R1 or
/RCH1 is necessary.
(For Standard model)
UT55A suffix code: Type 2 = 1, 2, 4, 5, or
7; UT52A suffix code: Type 2 = 1 or 2 is
necessary.
(For Detailed model)
DI16 is equipped when UT55A/UT52A
optional suffix code /R1 or /RCH1.
(For Standard model)
DI16 is equipped when UT55A suffix code:
Type 2 = 1, 2, 4, 5, or 7; UT52A suffix code:
Type 2 = 1 or 2.
8.1SettingControlMode(CTLM)

YOKOGAWA UT55A Specifications

General

Brand	YOKOGAWA
Model	UT55A
Category	Temperature Controller
Language	English