Alcatel-Lucent 9500 - Page 27

MPR-e and MSS-1c User Manual 3DB19901EFAA Edition 01 27
Figure 5.79 — MPT-HC V2/HC-HQAM/MPT-XP/XP-HQAM/9558HC 1+0 installation for integrated
antenna (external diplexer: vertical polarization).....................................................413
Figure 5.80 — MPT-HC/HC-HQAM/XP/XP-HQAM/9958HC 1+0 installation for integrated antenna
(external diplexer: horizontal polarization) ............................................................413
Figure 5.81 — "Pole Mounting for Remote ODU" installation .........................................................414
Figure 5.82 — Putting silicone grease on O-ring before MPT-HC/HC-HQAM/XP/XP-HQAM/9958HC
insertion ......................................................................................................415
Figure 5.83 — MPT-HC/HC-HQAM/XP/XP-HQAM/9958HC 1+0 installation for not integrated
antenna (embedded diplexer with pole mounting P/N 3DB10137AAXX) ...........................415
Figure 5.84 — MPT-HC/HC-HQAM/XP/XP-HQAM/9958HC 1+0 installation for not integrated
antenna (external diplexer with pole mounting P/N 3DB10137AAXX) ..............................416
Figure 5.85 — Coupler Polarization Change (11-38 GHz) - 1st Step and 2nd step ................................417
Figure 5.86 — Coupler Polarization Change (11-38 GHz) - 1st Step execution ....................................417
Figure 5.87 — Coupler Polarization Change (11-38 GHz) - 2nd Step execution ...................................418
Figure 5.88 — Coupler Polarization Change (11-38 GHz) - Screws fixing ...........................................418
Figure 5.89 — Putting silicone grease on O-ring before RF coupler insertion (11-38 GHz) ......................419
Figure 5.90 — Installing the RF coupler to the radio support (11-38 GHz) .........................................420
Figure 5.91 — PIPF indication and side pole ............................................................................420
Figure 5.92 — Putting silicone grease on RF coupler’s O-ring before MPT-HC/HC-HQAM insertion
(11-38 GHz)...................................................................................................421
Figure 5.93 — Installing the MPT-HC/HC-HQAM 1+1 on the RF coupler (11-38 GHz) .............................422
Figure 5.94 — Views of MPT-HC/HC-HQAM 1+1 integrated antenna after installation (11-38 GHz)............422
Figure 5.95 — Coupler Polarization Change (6-7-8 GHz) ..............................................................424
Figure 5.96 — Waterproofness tape ......................................................................................424
Figure 5.97 — Vertical polarization ......................................................................................425
Figure 5.98 — Top disk, showing V indication ..........................................................................425
Figure 5.99 — Bottom disk.................................................................................................425
Figure 5.100 — Bottom disk, after rotation.............................................................................426
Figure 5.101 — Top disk, showing H indication.........................................................................426
Figure 5.102 — Horizontal polarization..................................................................................426
Figure 5.103 — Installing the RF coupler to the radio support (6-7-8 GHz) ........................................427
Figure 5.104 — Putting silicone grease on O-ring before MPT-HC/HC-HQAM insertion (6-7-8 GHz)............428
Figure 5.105 — Installing the MPT-HC/HC-HQAM 1+1 on the RF coupler (6-7-8 GHz) ............................428
Figure 5.106 — Pole Mounting for Remote ODU installation..........................................................429
Figure 5.107 — Putting silicone grease on O-ring before RF coupler insertion ....................................430
Figure 5.108 — 11-38 GHz RF coupler installation (with pole mounting P/N 3DB10137AAXX) ..................430
Figure 5.109 — Putting silicone grease on RF coupler’s O-ring before MPT-HC/HC-HQAM
insertion (11-38 GHz) .......................................................................................431
Figure 5.110 — Installation of MPT-HC/HC-HQAM 1+1 (11-38 GHz) .................................................432
Figure 5.111 — Pole Mounting for Remote ODU installation..........................................................433
Figure 5.112 — Putting silicone grease on O-ring before RF coupler insertion ....................................433
Figure 5.113 — 6-7-8 GHz RF coupler installation (with pole mounting P/N 3DB10137AAXX)...................434
Figure 5.114 — Putting silicone grease on O-ring before MPT-HC/HC-HQAM insertion (6-7-8 GHz)............434
Figure 5.115 — Installing the MPT-HC/HC-HQAM 1+1 on the RF coupler (7-8 GHz)...............................435
Figure 5.116 — MPT-HC/HC-HQAM 1+1 installed on the RF coupler (6-7-8 GHz)..................................435
Figure 5.117 — On SBX-AMPT and SCX-AMPT antennas the radio interface is not present. .....................436
Figure 5.118 — Feeder plate and OMT antenna interface ............................................................437
Figure 5.119 — Insert the assembly in the antenna ...................................................................438
Figure 5.120 — Apply silicone grease when necessary before inserting the OMT .................................438