Alcatel-Lucent 9500 - Page 28

28 MPR-e and MSS-1c User Manual 3DB19901EFAA Edition 01
Figure 5.121 — Fix the fine tuning plate to the OMT body ...........................................................439
Figure 5.122 — Apply silicone grease if necessary .....................................................................440
Figure 5.123 — Fasten the MPT-HC/HC-HQAM/XP/XP-HQAM to the OMT ..........................................440
Figure 5.124 — MPT-HC/HC-HQAM/XP/XP-HQAM fastened to the OMT.............................................441
Figure 5.125 — Fine tuning ................................................................................................441
Figure 5.126 — Assemble the feeder and the feeder plate on the OMT interface................................442
Figure 5.127 — Insert the assembly in the antenna ...................................................................443
Figure 5.128 — Apply silicone grease ....................................................................................443
Figure 5.129 — Place and fix the OMT to the interface...............................................................444
Figure 5.130 — Engraved arrow toward pipe ...........................................................................445
Figure 5.131 — Apply silicone grease ....................................................................................445
Figure 5.132 — Locking hooks and fastening brackets ................................................................446
Figure 5.133 — Fine tuning ................................................................................................447
Figure 5.134 — Kit plug R2CT .............................................................................................448
Figure 5.135 — Kit plug R2CT items ......................................................................................448
Figure 5.136 — Remove the protection cap.............................................................................449
Figure 5.137 — Unscrew the nut spiral ..................................................................................449
Figure 5.138 — Pass cable through the mini kit plug ..................................................................449
Figure 5.139 — Crimp the RJ-45 plug ....................................................................................450
Figure 5.140 — EIA/TIA standard .........................................................................................450
Figure 5.141 — Insert the RJ-45 plug in the unlocking clip...........................................................450
Figure 5.142 — Insert the unlocking clip ................................................................................451
Figure 5.143 — Pull the coupling nut ....................................................................................451
Figure 5.144 — Return the cap ...........................................................................................451
Figure 5.145 — Tighten the nut spiral ...................................................................................452
Figure 5.146 — Cable is ready to be pulled .............................................................................452
Figure 5.147 — Align, insert and rotate the plug body................................................................453
Figure 5.148 — Connect the RJ-45 plug to its socket..................................................................453
Figure 5.149 — Push and rotate the coupling nut......................................................................453
Figure 5.150 — Secure the assembly .....................................................................................454
Figure 5.151 — Unscrew the nut spiral ..................................................................................454
Figure 5.152 — Rotate and unlock the coupling nut ...................................................................454
Figure 5.153 — Engage the RJ-45 unlocking clip .......................................................................455
Figure 5.154 — Press on the unlocking clip latch ......................................................................455
Figure 5.155 — Disconnect the RJ-45 plug ..............................................................................455
Figure 5.156 — Rotate and disconnect the R2CT plug body ..........................................................455
Figure 5.157 — LC/Q-XCO to LC Fiber cord .............................................................................456
Figure 5.158 — Fiber cable overlength box .............................................................................457
Figure 5.159 — XPIC connector position .................................................................................458
Figure 5.160 — XPIC connector position (with embedded XPIC on MPT-HC-HQAM/XP-HQAM) ..................459
Figure 5.161 — XPIC cable interconnection .............................................................................459
Figure 5.162 — XPIC cable interconnection (MPT-HC-HQAM/XP-HQAM) ............................................460
Figure 5.163 — MPT HC/XP grounding connector position............................................................463
Figure 5.164 — MPT HC-HQAM/XP-HQAM single-screw grounding connector position ...........................464
Figure 5.165 — MPT HC-HQAM/XP-HQAM double-screw grounding connector position ..........................465
Figure 5.166 — Grounding plate ..........................................................................................466
Figure 5.167 — Locations for cable grounds ...........................................................................467
Figure 5.168 — N connector waterproofing example..................................................................468
Figure 5.169 — Example of realization ..................................................................................469