Anritsu MT8820C - Page 63

63
2.3.3.1.2. Setting Example 2 (TDD)
The procedure at Chapter 2.3.3.1.1 is used, substituting the following steps to set Uplink/Downlink Configuration
and Special Subframe Configuration.
7. [PCC] Execute DLCHAN 38000 to set DL Channel and UL Channel to 38000 simultaneously.
8. [PCC] Execute DLCHAN_SCC1 39150 to set DL Carrier aggregation SCC-1 - DL Channel to 39150.
9. [PCC] Execute DLCHAN_SCC2 39500 to set DL Carrier aggregation SCC-2 - DL Channel to 39500.
14. [SCC-1] Execute ULCHAN_PCC 38000 to set DL Carrier aggregation PCC - UL Channel to 38000.
15. [SCC-1] Execute DLCHAN 39150 to set DL Channel to 39150.
19. [SCC-2] Execute ULCHAN_PCC 38000 to set DL Carrier aggregation PCC - UL Channel to 38000.
20. [SCC-2] Execute DLCHAN 39500 to set DL Channel to 39500.
23. [PCC/SCC] Execute TDDULDLCONF 1 to set TDD Uplink/Downlink Configuration to 1.
24. [PCC/SCC] Execute TDDSSFCONF 4 to set TDD Special Subframe Configuration to 4.
NOTE 1: Set the same value as Uplink/Downlink Configuration in PCC and SCC.
NOTE 2: Set the same value as Special Subframe Configuration in PCC and SCC.
2.3.3.2. MT8821C
2.3.3.2.1. Setting Example 1 (FDD)
23. Execute PRESET to set the default parameters.
24. Execute CHCODING RMC_DL_CA_PCC to set Common Parameter - Channel Coding to RMC (DL CA).
25. Execute DLSCC 2 to set Call Processing Parameter - Number of DL SCC to 2.
26. Execute CALLPROC ON to set Common Parameter - Call Processing to On.
27. Execute DLCHAN 300 to set Common Parameter - UL Channel and DL Channel to 18300 and 300,
respectively.
28. Execute DLCHAN_SCC1 2525 to set Common Parameter - SCC-1 - DL Channel to 2525.
29. Execute DLCHAN_SCC2 4450 to set Common Parameter - SCC-2 - DL Channel to 4450.
30. Execute BANDWIDTH 10MHZ to set Common Parameter - Channel Bandwidth to 10 MHz.
31. Execute BANDWIDTH_SCC1 20MHZ to set Common Parameter - SCC-1 - Channel Bandwidth to 20 MHz.
32. Execute BANDWIDTH_SCC2 10MHZ to set Common Parameter - SCC-2 - Channel Bandwidth to 10 MHz.
2.3.3.2.2. Setting Example 2 (TDD)
The procedure at Chapter 2.3.3.2.1 is used, substituting the following steps to set Uplink/Downlink Configuration
and Special Subframe Configuration.
5. Execute DLCHAN 38000 to set Common Parameter - DL Channel and UL Channel to 38000 simultaneously.
6. Execute DLCHAN_SCC1 39150 to set Common Parameter - SCC-1 - DL Channel to 39150.
7. Execute DLCHAN_SCC2 39500 to set Common Parameter - SCC-2 - DL Channel to 39500.
11. Execute TDDULDLCONF 1 to set Common Parameter - TDD Uplink/Downlink Configuration to 1.
12. Execute TDDSSFCONF 4 to set Common Parameter - TDD Special Subframe Configuration to 4.
NOTE 1: Set the same value as Uplink/Downlink Configuration in PCC and SCC.
NOTE 2: Set the same value as Special Subframe Configuration in PCC and SCC.
NOTE 3: The differential UL/DL Configuration on each CC is not supported.