Cisco Catalyst 2950

2-316
Catalyst 2950 and Catalyst 2955 Switch Command Reference
0L-10102-01
Chapter 2 Catalyst 2950 and 2955 Cisco IOS Commands
show controllers lre status
Switch# show controllers lre status profile
Port Link Uptime Profile DSRate USRate Fail
------ ---- -------- ------------------- ------ ------ ----
Lo0/1 UP 2d23h LRE-10 12.500 12.500 0
Lo0/2 UP 2d23h LRE-10 4.167 1.563 0
Lo0/3 UP 2d23h LRE-10 4.167 1.563 0
Lo0/4 UP 2d23h LRE-10 4.167 1.563 0
Lo0/5 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/6 UP 2d23h LRE-10 4.167 1.563 0
Lo0/7 UP 2d23h LRE-10 4.167 1.563 0
Lo0/8 UP 2d23h LRE-10 4.167 1.563 0
Lo0/9 UP 2d23h LRE-10 4.167 1.563 0
Lo0/10 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/11 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/12 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/13 UP 2d23h LRE-10 12.500 12.500 0
Lo0/14 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/15 UP 2d23h LRE-10 4.167 1.563 0
Lo0/16 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/17 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/18 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/19 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/20 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/21 UP 2d23h LRE-10 4.167 1.563 0
Lo0/22 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/23 DOWN 00:00:00 LRE-10 0.000 0.000 0
Lo0/24 DOWN 00:00:00 LRE-10 0.000 0.000 0
This is an example of output from the show controllers lre status psd command:
Switch# show controllers lre status psd
------- Switch ------------ ----------- CPE -----------
Port Link SNR RSErr TxPwr AGCgain SNR RSErr TxPwr AGCgain
------ ---- --- ---------- ------ ------- --- ---------- ------ -------
Lo0/1 UP 32 0 - 6.13 13.0 43 0 - 85.6 - 2.0
Lo0/2 UP 32 0 - 6.13 15.1 42 0 - 85.9 - 2.0
Lo0/3 UP 32 0 - 6.13 13.5 42 0 - 85.6 - 2.0
Lo0/4 DOWN 10 0 - 5.85 63.9 0 0 0.0 0.0
Lo0/5 DOWN 10 0 - 5.85 58.9 0 0 0.0 0.0
Lo0/6 UP 33 0 - 6.13 15.1 42 0 - 85.9 - 2.0
Lo0/7 DOWN 10 0 - 5.85 54.2 0 0 0.0 0.0
Lo0/8 UP 33 0 - 6.13 14.6 42 0 - 85.9 - 2.5
Lo0/9 DOWN 10 0 - 5.85 52.9 0 0 0.0 0.0
Lo0/10 DOWN 10 0 - 5.85 61.5 0 0 0.0 0.0
Lo0/11 UP 33 0 - 6.13 15.1 42 0 - 85.9 - 1.6
Lo0/12 UP 33 0 - 6.13 15.1 42 0 - 85.9 - 2.5
Lo0/13 UP 33 0 - 6.13 15.1 42 0 - 85.9 - 2.5
Lo0/14 DOWN 10 268305 - 5.85 57.5 0 0 0.0 0.0
Lo0/15 DOWN 10 0 - 5.85 50.7 0 0 0.0 0.0
Lo0/16 UP 35 38 - 5.85 15.1 41 1238 - 85.9 - 6.4
Lo0/17 DOWN 10 767128 - 5.85 61.8 0 0 0.0 0.0
Lo0/18 DOWN 10 0 - 5.85 54.2 0 0 0.0 0.0
Lo0/19 DOWN 10 0 - 5.85 51.5 0 0 0.0 0.0
Lo0/20 DOWN 10 0 - 5.85 54.7 0 0 0.0 0.0
Lo0/21 DOWN 10 0 - 5.85 67.8 0 0 0.0 0.0
Lo0/22 DOWN 10 0 - 5.85 50.7 0 0 0.0 0.0
Lo0/23 DOWN 10 0 - 5.85 66.5 0 0 0.0 0.0
Lo0/24 DOWN 10 0 - 5.85 53.6 0 0 0.0 0.0
This is an example of output from the show controllers lre status sequence command:
Switch# show controllers lre status sequence