EasyManua.ls Logo

D-Link DGS-3000 series - Page 725

D-Link DGS-3000 series
731 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
DGS-3000 Series Layer 2 Managed Gigabit Switch CLI Reference Guide
721
ningTrap
specific port changes from a stop_learning state
to a normal state, a trap will be sent out.
Binding: 1: swIpMacBindingPortIndex
swMacBasedAccessControlL
oggedSuccess
The trap is sent when a MAC-based access
control host is successfully logged in.
Binding: 1.swMacBasedAuthInfoMacIndex
2.swMacBasedAuthInfoPortIndex
3.swMacBasedAuthVID
1.3.6.1.4.1.171.12.35.11.1.0.1
swMacBasedAccessControlL
oggedFail
The trap is sent when a MAC-based access
control host login fails.
Binding: 1.swMacBasedAuthInfoMacIndex
2.swMacBasedAuthInfoPortIndex
3.swMacBasedAuthVID
1.3.6.1.4.1.171.12.35.11.1.0.2
swMacBasedAccessControl
AgesOut
The trap is sent when a MAC-based access
control host ages out.
Binding: 1.swMacBasedAuthInfoMacIndex
2.swMacBasedAuthInfoPortIndex
3.swMacBasedAuthVID
1.3.6.1.4.1.171.12.35.11.1.0.3
swERPSSFDetectedTrap
When the signal fail occurs, a trap will be
generated.
Binding: 1.swERPSNodeId
1.3.6.1.4.1.171.12.78.4.0.1
swERPSSFClearedTrap
When the signal fail clears, a trap will be
generated.
Binding: 1.swERPSNodeId
1.3.6.1.4.1.171.12.78.4.0.2
swERPSRPLOwnerConflictT
rap
When a conflict occurs, a trap will be generated.
Binding: 1.swERPSNodeId
1.3.6.1.4.1.171.12.78.4.0.3
swBpduProtectionUnderAtta
ckingTrap
When the BPDU Protection trap is enabled, if the
specific port changes from a normal state to an
under attack state, a trap will be sent out.
Binding: 1.swBpduProtectionPortIndex
2.swBpduProtectionPortMode
1.3.6.1.4.1.171.12.76.4.0.1
swBpduProtectionRecoveryT
rap
When the BPDU Protection trap is enabled, if the
specific port changes from an under attack state
to a normal state, a trap will be sent out.
Binding: 1.swBpduProtectionPortIndex
2.swBpduProtectionRecoveryMethod
1.3.6.1.4.1.171.12.76.4.0.2
swL2PortSecurityViolationTr
ap
When the port_security trap is enabled, if there's
a new MAC that violates the pre-defined port
security configuration, a trap will be sent out.
Binding: 1: swL2PortSecurityPortIndex
2: swL2PortSecurityViolationMac
1.3.6.1.4.1.171.11.133.1.1.2.1
00.1.2.0.2
1.3.6.1.4.1.171.11.133.2.1.2.1
00.1.2.0.2
swL2macNotification
This trap indicates the MAC address variations in
the address table.
Binding: 1: swL2macNotifyInfo
1.3.6.1.4.1.171.11.133.1.1.2.1
00.1.2.0.1
1.3.6.1.4.1.171.11.133.2.1.2.1
00.1.2.0.1
swPortLoopOccurred
The trap is sent when a Port loop occurs.
Binding: 1.swLoopDetectPortIndex
1.3.6.1.4.1.171.12.41.10.0.1
swPortLoopRestart
The trap is sent when a Port loop restarts after
the interval time.
Binding: 1.swLoopDetectPortIndex
1.3.6.1.4.1.171.12.41.10.0.2
swVlanLoopOccurred
The trap is sent when a Port with a VID loop
occurs.
Binding: 1.swLoopDetectPortIndex
2.swVlanLoopDetectVID
1.3.6.1.4.1.171.12.41.10.0.3

Table of Contents

Other manuals for D-Link DGS-3000 series

Related product manuals