What to do if position not reached during thread cutting on DURKOPP ADLER 867?
If the position is not reached during thread cutting or reversal on your DURKOPP ADLER Sewing Machine, check the controller settings and change them if required. Also, make mechanical adjustments to the machine, such as checking the thread cutter and belt tension. Ensure the thread lever is at the top dead center.
How to fix DA stepper card 1 flywheel position not found on DURKOPP ADLER 867?
If the DA stepper card 1 flywheel position is not found on your DURKOPP ADLER Sewing Machine, check the connection cables and inspect stepper motor 1 for stiff movement.
What to do if there is sewing motor insulation fault on DURKOPP ADLER 867 Sewing Machine?
If there is a sewing motor insulation fault on your DURKOPP ADLER Sewing Machine, check the sewing motor phase and PE for low-impedance connection. Replacing the encoder or sewing motor might be necessary.
How to fix incorrect sewing motor direction of rotation on DURKOPP ADLER Sewing Machine?
If the sewing motor direction of rotation is incorrect on your DURKOPP ADLER Sewing Machine, replace the encoder. Also, check the plug assignment and wiring in the machine distributor, and test the sewing motor phases to ensure they have the correct value.
What to do if maximum speed exceeded on DURKOPP ADLER 867 Sewing Machine?
If the maximum speed is exceeded on your DURKOPP ADLER Sewing Machine, replace the encoder, perform a reset, and check the class (t 51 04).
How to troubleshoot error in the reference run on DURKOPP ADLER 867 Sewing Machine?
If there is an error in the reference run on your DURKOPP ADLER Sewing Machine, replace the encoder and eliminate any stiff movement in the sewing machine.
How to fix checksum error during update on DURKOPP ADLER Sewing Machine?
If you encounter a checksum error during update on your DURKOPP ADLER Sewing Machine, check the connection cables. You may also try a software update or replace the DACextension box.
What to do if DA stepper card 1 boot error on DURKOPP ADLER 867 Sewing Machine?
If you encounter a DA stepper card 1 boot error on your DURKOPP ADLER Sewing Machine, check the connection cables. You may also try a software update or replace the DACextension box.
General| Stitch Type | Lockstitch |
|---|---|
| Max Stitch Length | 12 mm |
| Needle System | 134-35 |
| Needle Thread Tension | Adjustable |
| Lubrication | Automatic |
| Type | Industrial Sewing Machine |
| Max Sewing Speed | 3000 stitches per minute |
| Presser Foot Lift | 20 mm |
| Power Requirements | 230V/50Hz |
Identifies the target audience for the service instructions.
Explains symbols and formatting used for clarity in the manual.
Lists related documentation for further reference.
Outlines the manufacturer's liability limitations.
Provides fundamental safety guidelines for machine operation and maintenance.
Details hazard levels and associated symbols for safety alerts.
Emphasizes adjustment sequence and proper cable routing.
Explains procedures for accessing machine components by removing covers.
Describes shaft features and methods to secure the machine for adjustments.
Instructions for positioning the handwheel to specific marks for adjustments.
Step-by-step guide for recalibrating the handwheel's graduated scale.
Procedure to correctly position the arm shaft for proper machine function.
Instructions for aligning both upper and lower toothed belt wheels.
Detailed steps for adjusting the primary and secondary stitch length controls.
Setting stitch length limits and adjusting for forward/backward stitch consistency.
How to set feed dog position and adjust its movement cycle for accurate feeding.
Setting and adjusting the feed dog's lift height using different methods.
Procedures for aligning the needle bar linkage sideways and in the sewing direction.
Setting hook-needle clearance and synchronizing loop formation.
Adjusting the needle guard and needle bar height for correct needle-hook interaction.
Setting the lifting gap and synchronizing the bobbin case lifter's operation.
Adjusting sewing foot lift height, stroke, and pressure for material.
Fine-tuning the walking foot's movement relative to the feed dog.
Adjusting needle thread tension using the regulator and spring.
Aligning winder components and adjusting the hook thread guide.
Adjusting the winder's operation and determining bobbin fill quantity.
Adjusting knife height and the path of the thread-cutting action.
Setting cutting pressure and synchronizing the thread cutting operation.
Overview, locking latch, thread-pulling knife, counter blade, and timing adjustments for KFA.
Procedure for setting the potentiometer via the control panel.
Attaching the safety clutch and setting its torque for proper disengagement.
Identifies drive components and explains disassembly/assembly procedures.
Procedures for replacing the sewing light fuse and the main printed circuit board.
Details needle bar height and slide adjustments for these machines.
Setup and fine adjustment for machines with a moving binder.
Adjustments for knife movement time, stroke, blade overlap, and cutting edge settings.
How to activate the tensioner lift and Needle Stop Brake (NSB) functions.
Procedures for cleaning the machine and lubricating its components.
Maintenance for operating pressure, water-oil draining, and filter cleaning.
Cleaning the motor fan mesh and checking the toothed belt.
Information on how to obtain a parts list for the machine.
Steps to safely take the machine out of service.
Guidelines for environmentally responsible disposal of the machine.
Contact info for support and interpretation of software messages.
Common sewing issues, causes, and solutions.
Machine's noise levels and technical specifications by subclass.
Maximum operating speeds and requirements for reliable performance.
Electrical schematics and wiring layouts for the machine.
To Next Page