Edge-Core EAP8518 User Manual

C HAPTER 28 | Link Layer Discovery Commands
– 224 –
EXAMPLE
AP(config)# lldp transmit interval 30
AP(config)#
lldp transmit re-init-
delay
This command configures the delay before attempting to re-initialize after
LLDP ports are disabled or the link goes down.
SYNTAX
lldp transmit re-init-delay <seconds>
seconds - Time in seconds. (Range: 2 - 10)
DEFAULT SETTING
2 seconds
COMMAND MODE
Global Configuration
COMMAND USAGE
◆ This command configures the delay before attempting to re-initialize
after LLDP ports are disabled or the link goes down.
◆ When LLDP is re-initialized on a port, all information in the remote
systems LLDP MIB associated with this port is deleted.
EXAMPLE
AP(config)#lldp transmit re-init-delay 10
AP(config)#
lldp transmit delay-
to-local-change
This command configures a delay between the successive transmission of
LLDP advertisements initiated by a change in local LLDP MIB variables.
SYNTAX
lldp transmit delay-to-local-change <seconds>
seconds - Time in seconds. (Range: 1-8192 seconds)
DEFAULT SETTING
2 seconds
COMMAND MODE
Global Configuration
COMMAND USAGE
◆ The transmit delay is used to prevent a series of successive LLDP
transmissions during a short period of rapid changes in local LLDP MIB

Edge-Core EAP8518 Specifications

General

Model	EAP8518
Type	Wireless Access Point
Wireless Standards	IEEE 802.11a/b/g/n/ac/ax
Frequency Bands	2.4 GHz, 5 GHz
Mounting Options	Ceiling, Wall
PoE	802.3af/at
Antenna Type	Internal
Management	Web-based, SNMP
Security	WPA3, WPA2, WPA

Summary

EAP8518 802.11n Access Point User Guide

Getting Started

Introduction to the EAP8518 Access Point

Overview of the EAP8518, its standards, and features.

Network Topologies

Describes different wireless network configurations and concepts.

Installing the Access Point

Provides instructions for physical installation of the access point.

Initial Configuration Steps

Guides through basic system identification, password, and country code.

Web Interface Configuration

System Settings

Basic system settings including name, IP, RADIUS, time, and logs.

Management Settings

Configuration for remote access protocols like Telnet, SSH, HTTP, SNMP.

Advanced Settings

Access Control Lists (ACLs)

Filters traffic based on MAC addresses for security.

Wireless Settings

Spanning Tree Protocol (STP)

Manages network loops and provides redundant links.

Authentication Methods

Configures local MAC or RADIUS authentication for wireless clients.

Radio Settings

Configures channel, transmit power, SSID, and security for wireless.

Wireless Security Settings

Configures association modes, encryption, and authentication for wireless security.

Maintenance Settings

Status Information

Command Line Interface (CLI)

Using the Command Line Interface

Introduction to accessing and navigating the CLI.

General CLI Commands

System Management CLI Commands

System Logging CLI Commands

System Clock and SNTP CLI Commands

DHCP Relay CLI Commands

SNMP CLI Commands

SNMPv3 User Configuration

Manages SNMPv3 users, groups, and security levels.

Flash/File Management Commands

RADIUS Client CLI Commands

RADIUS Server Configuration

Enables and configures primary/secondary RADIUS servers.

802.1X Authentication CLI Commands

MAC Address Authentication CLI Commands

Filtering CLI Commands

Local Bridge Filter Configuration

Controls communication between wireless clients on the same VAP.

Spanning Tree CLI Commands

WDS Bridge CLI Commands

WDS AP and STA Mode Configuration

Configures access points for Wireless Distribution System links.

Ethernet Interface CLI Commands

Wireless Interface CLI Commands

Virtual Access Points (VAPs)

Manages multiple SSIDs and network segments on the access point.

Radio Channel and Throughput Settings

Configures the radio channel and high throughput mode.

Wireless Security CLI Commands

Authentication Type Configuration

Sets client authentication methods like Open, WPA, WPA2.

Encryption Method Configuration

Configures encryption ciphers like WEP, TKIP, AES-CCMP.

WPA Pre-Shared Key Configuration

Configures WPA/WPA2 pre-shared keys for network access.

Link Layer Discovery CLI Commands

VLAN CLI Commands

WMM QoS CLI Commands

Appendices

Troubleshooting Guide

Provides guidance on diagnosing and resolving common issues.

Hardware Specifications

Details technical specifications like power, sensitivity, and frequency.

Cables and Pinouts

Information on RJ-45 connectors, wiring standards, and pinouts.