HP xw4600 User Manual

Screen message Probable cause Recommended action
1781—Disk 1 Failure The drive is not installed correctly or
has failed.
1. Be sure that any jumpers are set correctly and that
power and drive cables are connected, both to the
drive and the system board.
2. Verify that the cables are the correct cables for
your computer model. If this message persists,
your workstation might require service.
1782—Disk Controller Failure Hard drive circuitry error. 1. Run the Computer Setup (F10) utiltiy.
2. Clear CMOS.
3. Verify cable seating and jumper settings.
4. Run hard-drive diagnostics.
5. Disconnect additional drives.
6. Run the Drive Protection System test (if available).
7. Replace the hard drive.
8. Replace the system board.
1790—Disk 0 Error The drive is not installed correctly or
has failed.
1. Be sure that any jumpers are set correctly and that
power and drive cables are connected to both the
hard drive and the system board.
2. Verify that the cables are the correct cables for
your computer model. If this message persists,
you may need service for your workstation.
1791—Disk 1 Error The drive is not installed correctly or
has failed.
1. Be sure that any jumpers are set correctly and that
power and drive cables are connected to both the
hard drive and the system board.
2. Verify that the cables are the correct cables for
your computer model. If this message persists,
you may need service for your workstation
1792—Secondary Disk
Controller Failure
Hard drive circuitry error. 1. Run the Computer Setup (F10) utilty.
2. Clear CMOS.
3. Verify cable seating/jumper settings.
4. Run hard-drive diagnostics.
5. Disconnect additional drives.
6. Run the Drive Protection System test (if available).
7. Replace the hard drive.
1793—Secondary Controller
or Disk Failure
Hard drive circuitry error. 1. Run the Computer Setup (F10) Utility.
2. Clear CMOS.
3. Verify cable seating and jumper settings.
4. Run hard-drive diagnostics.
5. Disconnect additional drives.
Table 5-18 POST error messages (continued)
ENWW POST error messages 139

HP xw4600 Specifications

General

Tcase	72.4 °C
Bus type	FSB
Stepping	E0
Processor cache	6 MB
Processor cores	2
Processor model	E8400
System bus rate	- GT/s
Processor family	Intel® Core™2 Duo
Processor series	Intel Core 2 Duo E8000 Series
Processor socket	LGA 775 (Socket T)
Processor codename	Wolfdale
Processing Die size	107 mm²
Processor frequency	3 GHz
Processor cache type	L2
Processor lithography	45 nm
Processor manufacturer	Intel
Processor front side bus	1333 MHz
Processor operating modes	64-bit
ECC supported by processor	No
Thermal Design Power (TDP)	65 W
Number of processors installed	1
CPU multiplier (bus/core ratio)	9
Number of Processing Die Transistors	410 M
Audio system	High Definition Audio
Product type	Workstation
Motherboard chipset	Intel® X38 Express
ECC	Yes
Internal memory	2 GB
Memory clock speed	800 MHz
Internal memory type	DDR2-SDRAM
Maximum internal memory	8 GB
Memory layout (slots x size)	2 x 1 GB
HDD speed	7200 RPM
HDD capacity	250 GB
HDD interface	SATA
Optical drive type	DVD-RW
Graphics card	-
Networking features	Gigabit Ethernet (10/100/1000)
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power supply	475 W
Chassis type	Tower
Country of origin	China
Processor code	SLB9J
Processor ARK ID	33910
Processor package size	37.5 x 37.5 mm
On-board graphics card model	Not available

Weight and Dimensions

Depth	456 mm
Width	168 mm
Height	450 mm
Weight	19000 g