Intermac Primus 184 - 2.5 Beam of X and Y axes

132 pages

Save Page as PDF

To Next Page

To Previous Page

2 Machine description

2.5 Beam of X and Y axes

The mobile beam sustains the working head carriage. It forms the X-axis of the machine and slides

on two guides with ball blocks (Y-axis) that are located on the sides of the base.

The beam moves with the aid of a pinion, rack and two brushless motors (one per side).

Main Page

Information about the publication3
Index5
Introduction9
- Conventions9
- Documents supplied with the machine10
- CE declaration of conformity11
- Links related to the PC use11
1 Safety information13
- 1.1 First aid and medical assistance13
- 1.2 Lifting and handling15
- 1.3 Installation15
- 1.4 Protection against overcurrents15
- 1.5 Protection against indirect contacts16
- 1.6 Protection against fire16
- 1.7 Preparation and machining operations16
- 1.8 Maintenance17
- 1.9 Scrapping18
- 1.10 Danger signs19
- 1.11 General prohibition signs19
- 1.12 Obligation signs20
- 1.13 Signs fixed to the machine20
2 Machine description21
- 2.1 General description of the machine21
- 2.2 Configurations of the Primus line22
- 2.3 Primus overview and main parts24
- 2.4 Base and basin25
- 2.5 Beam of X and Y axes26
- 2.6 3-axis working head (X, Y, Z)27
- 2.7 5-axis working head (X, Y, Z, A, C)28
- 2.8 Work table29
- 2.9 Safety devices30
- 2.10 Identification of the manufacturer and the machine31
3 Basic concepts33
- 3.1 Axes33
- 3.2 Manual movement of the axes34
- 3.3 Axis transfer speed change34
- 3.4 Working areas34
- 3.5 Origins34
- 3.6 Machine operation35
4 Intended use and unintended use37
- 4.1 How to use the machine37
- 4.2 Characteristics and dimensions of workable materials38
- 4.3 Executable machining operations39
- 4.4 Personnel qualifications40
- 4.5 Work area40
  - Machine location40
- 4.6 Danger area41
- 4.7 Residual risks41
5 Commands and indicator devices43
- 5.1 Layout of the commands and indicator devices - Primus44
- 5.2 Main control panel45
  - Primus 18445
  - PRIMUS 322/324/32646
- 5.3 hand-held button pad47
  - Type RM85047
  - 5.3.1 Using the hand-held button pad49
6 Preparing the operating section51
- 6.1 Cutting unit51
- 6.2 Machining parameters51
7 Anti-collision thickness tracer53
- 7.1 General remarks53
- 7.2 Use53
8 Using the machining water recirculation system55
- 8.1 Lifting55
- 8.2 Physical treatment55
- 8.3 Extraction of the suspended solids56
  - Characteristics of the treated water56
9 Basic use57
- 9.1 Machine start-up57
- 9.2 Resetting the machine axes58
- 9.3 Stopping the machine functions58
- 9.4 Restoring normal machine functioning59
- 9.5 Switching the machine off59
- 9.6 Using the abrasive distribution system (optional)60
10 Carrying out machining operations61
- 10.1 Warnings relating to machining operations61
- 10.2 Machining operation procedure62
- 10.3 Origin management and selection62
  - Origins management62
  - Description of the parameters63
- 10.4 Positioning and locking the piece63
- 10.5 Using the machine in manual mode (axis movement)64
- 10.6 Using the machine in automatic mode64
- 10.7 Starting the machining operation64
- 10.8 Working cycle64
- 10.9 Machining identical pieces65
- 10.10 Unloading the piece65
- 10.11 Interrupting the machining operation66
11 Routine and special maintenance67
- 11.1 Routine maintenance68
- 11.2 Special maintenance85
12 Technical characteristics87
- 12.1 Layout88
- 12.2 General data92
- 12.3 General intensifier data92
- 12.4 Admissible weight on the work table93
- 12.5 Water consumption93
- 12.6 Electrical characteristics93
- 12.7 Lighting93
- 12.8 Main machine axes - X, Y, Z94
- 12.9 Noise level95
  - Primus 18495
  - Primus 322/32495
13 Handling and transport97
- 13.1 Warnings concerning machine transportation and installation97
- 13.2 Parts to be transported98
- 13.3 Unloading the machine99
14 Installation and assembly103
- 14.1 Machine layout, connection points and working dimensions103
- 14.2 Installation area requisites103
- 14.3 Layout of the support feet106
- 14.4 Levelling of the machine108
- 14.5 Safety guards110
- 14.6 Connecting the machine to the hydraulic system111
  - Connection to the main water supply111
- 14.7 Connecting the machine to the electric system112
  - 14.7.1 Connection cable113
  - 14.7.2 Power levels of the Primus 184/322/324113
- 14.8 Connecting the machine to the pneumatic system114
- 14.9 Equipment supplied114
15 Decommissioning - demolition115
16 Warranty and customer service117
- 16.1 Warranty117
- 16.2 Customer service117
17 Message list119
18 Enclosures121
- Abrasive powder toxicological datasheet121
- GMA GARNET (EUROPE) GmbH121
- Torque_Hpcomponents122
19 Drawings and diagrams123
Analytical Index125
- A125
- B125
- C125
- D126
- E126
- F126
- G126
- H126
- I126
- K126
- L126
- M127
- N128
- O128
- P128
- Q128
- R128
- S128
- T129
- U129
- W129
- X129

Intermac Primus 184 - 2.5 Beam of X and Y axes

Table of Contents