Keithley 2001 User Manual

SCPI Conformance Information
J-11
[:SENSe[1]]
:CURRent:DC
:AVERage
:ADVanced
:NTOLerance <n>
:NTOLerance?
[:STATe] <b>
[:STATe]?
[:STATe] <b>
[:STATe]?
:AUTO <b>
:AUTO ONCE
:AUTO?
:METHod <name>
:METHod?
:VOLTage:AC
:APERture
:AUTO <b>
:AUTO ONCE
:AUTO?
:NPLCycles
:AUTO <b>
:AUTO ONCE
:AUTO?
:COUPling AC|DC
:COUPling?
:RANGe
:AUTO
:ULIMit <n>
:ULIMit?
:LLIMit <n>
:LLIMit?
:REFerence
:ACQuire
:DIGits <n>
:AUTO <b>
:AUTO ONCE
:AUTO?
:DIGits?
:AVERage
:TCONtrol <name>
:TCONtrol?
:COUNt <n>
:COUNt?
:ADVanced
:NTOLerance <n>
:NTOLerance?
[:STATe] <b>
[:STATe]?
[:STATe] <b>
[:STATe]?
:AUTO <b>
:AUTO ONCE
:AUTO?
Path to configure and control advanced filter.
Specify noise tolerance level (0 to 100 percent).
Query noise tolerance level.
Enable (1 or ON) or disable (0 or OFF) advanced filter.
Query state of advanced filter.
Enable (1 or ON) or disable (0 or OFF) filter.
Query state of digital filter.
Enable (1 or ON) or disable (0 or OFF) auto filter.
Enable and then disable auto filter.
Query auto filter.
Select measurement technique: NORMal, ICIRcuit.
Query method.
Path to configure AC voltage
Specify integration rate in seconds (166.67e-6 to 200e-3).
Enable (1 or ON) or disable (0 or OFF) auto aperture.
Enable and then disable auto aperture.
Query auto aperture (0 or 1).
Specify integration rate (number of line cycles; 0.01 to 10).
Enable (1 or ON) or disable (0 or OFF) auto NPLC.
Enable and then disable auto NPLC.
Query auto line cycle integration (0 or 1).
Specify input coupling.
Query input coupling.
Path to configure measurement range:
Set range based on present input signal.
Specify upper limit for auto range (0 to +775).
Query upper limit.
Specify lower limit for auto range (0 to +775).
Query lower limit.
Specify reference (REL) value (-775 to +775).
Use input signal as reference.
Specify measurement resolution (4 to 8).
Enable (1 or ON) or disable (0 or OFF) auto resolution.
Enable and then disable auto resolution.
Query auto resolution (0 or 1).
Query resolution.
Path to configure and control the filter.
Select filter type: MOVing, REPeat.
Query filter type.
Specify filter count (1 to 100).
Query filter count.
Path to configure and control advanced filter.
Specify noise tolerance level (0 to 100 percent).
Query noise tolerance level.
Enable (1 or ON) or disable (0 or OFF) advanced filter.
Query state of advanced filter.
Enable (1 or ON) or disable (0 or OFF) filter.
Query state of digital filter.
Enable (1 or ON) or disable (0 or OFF) auto filter.
Enable and then disable auto filter.
Query auto filter.
Table J-2 (cont.)
Syntax of non-SCPI commands implemented by Model 2001
Command Description

Keithley 2001 Specifications

General

Brand	Keithley
Model	2001
Category	Multimeter
Language	English