Lexmark C760 - Page 447

Index I-5
5060-4xx
PRINT TESTS
Print Quality Pgs
3-19, B-3
Quick Test Page 3-19
printer alignment procedures 4-61, 4-63
printhead diagnostics 3-1
printhead electronic alignment 4-63
printhead electronic alignment test pages B-10
Printhead Inst 3-18
printhead interlock switch, service check 2-110
printheads
diagnostics aid
3-1
electronic alignment 4-63
identification 4-60
location 5-2
parts catalog 7-13
removal 4-61
Prt Quality Pgs 3-9
Q
Quick Disk Test 3-30
Quick Test Page 3-15, 3-19, B-8
Quick Test, duplex 3-24
R
rear bellcrank
parts catalog
7-25
removal 4-64, 4-66
redrive assembly
belt routing
A-6
parts catalog 7-14
removal 4-68
REGISTRATION 3-14
registration motor
location
5-2
parts catalog 7-17
removal 4-69
removals
autocompensator pick assembly
4-20
BOR drive assembly 4-28
cartridge contact assembly 4-29
cartridge drive assembly 4-30
covers
front cover assembly
4-14
front left handle cover assembly 4-10, 4-11
front lower left cover 4-10
front lower right cover 4-12
front right handle cover assembly 4-13
left lower cover 4-18
lower jam access door assembly 4-19
lower right door assembly 4-18
paper path access door cover 4-11
rear cover 4-16
redrive door 4-19
top cover assembly 4-6
developer HVPS board 4-31
friction buckler 4-33
front right light shield 4-34
fuser assembly 4-35
fuser bottom duct 4-36
fuser drive assembly 4-37
fuser drive card assembly 4-37
fuser fan 4-38
fuser top duct 4-39
fuser web oiler motor assembly and card 4-40
inner system board shield 4-43
ITU assembly 4-44
ITU drive assembly 4-44
ITU drive motor 4-45, 4-69
LVPS assembly 4-46
multipurpose feeder (MPF) 4-48
nip relief handle 4-50
operator panel 4-53
outer system board shield 4-54
paper size sensing assembly 4-55
paper size sensing board 4-58
pick rolls 4-58
printheads 4-60
rear bellcrank (black) 4-66
rear bellcrank (cyan, magenta, yellow) 4-64
redrive assembly 4-68
registration motor 4-69
RIP fan 4-69
S2/narrow media/transparency/mutipurpose feeder
cables
4-70
S2/narrow media/transparency/mutipurpose feeder
sensors
4-71
second transfer roll 4-71
system board 4-72
transfer HVPS board 4-73
transfer plate assembly 4-76
vacuum transport belt (VTB) 4-77
vacuum transport belt (VTB) fan 4-79
waste container door 4-79
waste container latch 4-80
web oiler fuser kit installation 4-80
Reset Calibration 3-34
Reset Fuser Count 3-9
resolution 1-3
RIP fan
location
5-2
removal 4-69
service check 2-86
ROM Test 3-22
S
S2 sensor cable, removal 4-70
S2 sensor, removal 4-71
safety information xv
safety inspection guide 6-1
screw identification table 4-2
second transfer roll
parts catalog
7-12
removal 4-71
service check 2-141
Sensor Test 3-25, 3-27
sensors
location
5-3
paper out, MPF 7-15
paper size 7-16