What to do if my Lexmark MS711 says 'Insufficient memory, some held jobs will not be restored'?
If your Lexmark printer displays an 'Insufficient memory, some held jobs will not be restored' message, you can press on the printer control panel to clear the message. You can also delete other held jobs to free up additional printer memory.
What to do if my Lexmark Printer says 'Memory full'?
If your Lexmark Printer displays a 'Memory full' message, you can try the following: First, press on the printer control panel to clear the message. If the problem persists, decrease the resolution setting or install additional printer memory.
How to fix 'Incorrect paper size, open [paper source]' on Lexmark Printer?
If your Lexmark printer displays an 'Incorrect paper size' message, try these steps: Load the correct size of paper in the tray. You can also press on the printer control panel to clear the message and print using a different tray. Check the tray length and width guides to ensure the paper is loaded properly. Also, verify that the correct paper size and type are specified in Print Properties, the Print dialog, or the Paper menu on the printer control panel. If the MP Feeder Size is set to Universal, ensure the paper is large enough for the data being printed. As a last resort, cancel the print job.
What to do if Lexmark Printer displays 'Load staples'?
If your Lexmark printer is showing a 'Load staples' message, you should replace or insert the specified staple cartridge in the finisher. Alternatively, you can press on the printer control panel to clear the message and continue printing, or cancel the print job.
What to do if Lexmark MS711 says 'Check tray [x] connection'?
If your Lexmark printer displays a 'Check tray connection' message, try turning the printer off and then back on. If the error persists, turn off the printer, unplug the power cord, remove the specified tray, reattach it, reconnect the power cord, and then turn the printer back on. If the error occurs again, repeat the above steps and then contact customer support. You can also press on the printer control panel to clear the message and continue printing.
What to do if Lexmark Printer displays 'Insert hole punch box'?
If your Lexmark printer displays an 'Insert hole punch box' message, insert the hole punch box into the finisher and then press on the printer control panel to clear the message.
What to do if Lexmark Printer displays 'Incompatible output bin [x]'?
If your Lexmark printer displays an 'Incompatible output bin' message, remove the specified bin. Alternatively, you can press on the printer control panel to clear the message and continue printing without using the specified bin.
What to do if Lexmark MS711 Printer displays 'Incompatible tray [x]'?
If your Lexmark printer displays an 'Incompatible tray' message, remove the specified tray. Alternatively, you can press on the printer control panel to clear the message and continue printing without using the specified tray.
How to fix 'Disk must be formatted for use in this device' error on Lexmark MS711?
If your Lexmark printer displays the message 'Disk must be formatted for use in this device,' select 'Format disk' from the printer control panel to format the printer hard disk and clear the message.
What does 'Cartridge, imaging unit mismatch' mean on my Lexmark MS711 and how to fix it?
If your Lexmark printer displays a 'Cartridge, imaging unit mismatch' error, check if both the toner cartridge and imaging unit are MICR (Magnetic Ink Character Recognition) or non-MICR supplies. Change either the toner cartridge or the imaging unit, so that both are either MICR or non-MICR.
General| Print Resolution | 1200 x 1200 dpi |
|---|---|
| Operating Systems Supported | Windows, macOS, Linux |
| Print Technology | Laser |
| Processor Speed | 800 MHz |
| Standard Memory | 512 MB |
| Maximum Memory | 1.5 GB |
| Output Capacity | 250 sheets |
| Hard Drive | Optional |
| Energy Star Certified | Yes |
| Printer Type | Monochrome Laser |
| Connectivity | USB, Ethernet |
| Duplex Printing | Automatic |
| Print Languages | PostScript 3 |
| Dimensions (W x D x H) | 15.7 x 17.5 x 15.7 inches |
To Next Page
