printer
configurations 779
finishing features 49
models 779
printer control panel
indicator light 322
parts 321
Sleep button light 322
using 321
printer messages
[x]‑page jam, clear manual feeder. [250] 120
[x]‑page jam, lift front cover to remove cartridge.
[200–201] 66
[x]‑page jam, open tray [x]. [24x] 96
[x]‑page jam, open upper and lower rear door. [231–
234] 87
[x]‑page jam, open upper rear door. [202] 78
[x]‑page jam, remove paper, open expander rear
door. Leave paper in bin. [41y.xx] 123
[x]‑page jam, remove paper, open finisher rear
door. Leave paper in bin. [451] 126
[x]‑page jam, remove paper, open mailbox rear
door. Leave paper in bin. [43y.xx] 124
[x]‑page jam, remove paper, open stapler door. Leave
paper in bin. [455–457] 127
[x]‑page jam, remove standard bin jam. [203] 85
[x]‑page jam, remove tray 1 to clear duplex. [235–
239] 89
Cartridge low [88.xy] 213
Cartridge nearly low [88.xy] 213
Cartridge very low, [x] estimated pages remain
[88.xy] 213
Cartridge, imaging unit mismatch [41.xy] 213
Change [paper source] to [custom string] load
[orientation] 213
Change [paper source] to [custom type name] load
[orientation] 214
Change [paper source] to [paper size] load
[orientation] 214
Change [paper source] to [paper type] [paper size]
load [orientation] 214
Check tray [x] connection 214
Close door or insert cartridge 215
Close rear door 215
Complex page, some data may not have printed
[39] 215
Configuration change, some held jobs were not
restored [57] 215
Defective flash detected [51] 215
Disk must be formatted for use in this device 215
Disk near full. Securely clearing disk space. 216
Empty the hole punch box 216
Error reading USB drive. Remove USB. 216
Error reading USB hub. Remove hub. 216
Imaging unit low [84.xy] 216
Imaging unit nearly low [84.xy] 216
Imaging unit very low, [x] estimated pages remain
[84.xy] 216
Incompatible output bin [x] [59] 217
Incompatible tray [x] [59] 217
Incorrect paper size, open [paper source] [34] 217
Insert hole punch box 217
Insert staple cartridge 217
Insert Tray [x] 218
Install bin [x] 218
Install Tray [x] 218
Insufficient memory for Flash Memory Defragment
operation [37] 218
Insufficient memory to collate job [37] 219
Insufficient memory to support Resource Save feature
[35] 219
Insufficient memory, some Held Jobs were deleted
[37] 218
Insufficient memory, some held jobs will not be
restored [37] 219
Load [paper source] with [custom string] [paper
orientation] 219
Load [paper source] with [custom type name] [paper
orientation] 220
Load [paper source] with [paper size] [paper
orientation] 220
Load [paper source] with [paper type] [paper size]
[paper orientation] 220
Load manual feeder with [custom string] [paper
orientation] 220
Load manual feeder with [custom type name] [paper
orientation] 221
Load manual feeder with [paper size] [paper
orientation] 221
Load manual feeder with [paper type] [paper size]
[paper orientation] 221
Load staples 219
Maintenance kit low [80.xy] 221
Maintenance kit nearly low [80.xy] 221
Maintenance kit very low, [x] estimated pages remain
[80.xy] 222
Memory full [38] 222
Network [x] software error [54] 222
Non‑Lexmark [supply type], see User’s Guide
[33.xy] 222
Not enough free space in flash memory for resources
[52] 223
Paper changes needed 223
Parallel port [x] disabled [56] 223
4063
Index
916
To Next Page
Loading...
