NETGEAR GS324T User Manual

S350 Series 24-Port (PoE+) and 48-Port Gigabit Ethernet Smart Managed Pro Switches
Manage Device Security User Manual285
You can select either the Port radio button or the Range radio button:
- Port. If you select the Port radio button, you can either enter the port number
yourself or select one of the following protocols from the menu:
• The source IP TCP port protocols are
Domain, Echo, FTP, FTP data,
www-http, SMTP, Telnet, POP2, POP3, and bgp.
• The source IP UDP port protocols are Domain, Echo, SNMP, NTP, RIP, Time
,
Who, and TFTP.
Each of these values translates into its equivalent port number, which is used as
both the start and end of the port range.
Select Other from the menu to enter a port number. If you select Other from the
menu but leave the field blank, it means any.
The relevant matching conditions for L4 port numbers are as follows:
• Equal. IP ACL rule matches only if the Layer 4 source port number is equal to
the specified port number or port protocol.
•
Less Than. IP ACL rule matches if the Layer 4 source port number is less
than the specified port number
.
• Greater Than. IP ACL rule matches if the Layer 4 source port number is
greater than the specified port number
.
• Not Equal. IP ACL rule matches only if the Layer 4 source port number is not
equal to the specified port number or port protocol.
-
Range. If you select the Range radio button, the IP ACL rule matches only if the
Layer 4 source port number is within the specified port range.
The starting port,
ending port, and all ports in between are a part of the Layer 4 port range.
The Start Port and End Port fields identify the first and last ports that are part of
the port range. The values can range from 0 to 65535.
Y
ou can either enter the port range yourself or select one of the following
protocols from the menu:
• The source IP TCP port range names are Domain, Echo, FTP, FTP data,
www-http, SMTP, Telnet, POP2, POP3, and bgp.
• The source IP UDP port range names are Domain, Echo, SNMP, NTP, RIP,
Time
, Who, and TFTP.
Each of these values translates into its equivalent port number, which is used as
both the start and end of the port range. Select Other from the menu to enter a
port number. If you select Other from the menu but leave the field blank, it means
any.
The wildcard mask determines which bits are used and which bits are ignored. A
wildcard mask of 0.0.0.0 indicates that none of the bits are important. A wildcard
of 255.255.255.255 indicates that all of the bits are important.

NETGEAR GS324T Specifications

General

Switch type	Managed
Switch layer	L2/L3/L4
ARP inspection	Yes
Master (outer) case width	270 mm
Master (outer) case height	271 mm
Master (outer) case length	481 mm
Master (outer) case weight	8850 g
Harmonized System (HS) code	85176990
Quantity per master (outer) case	3 pc(s)
Package type	Box
Package depth	465 mm
Package width	229 mm
Package height	79 mm
Package weight	2710 g
Cables included	AC
Stackable	-
Product color	Black
Input current	5 A
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	13.5 W
Operating temperature (T-T)	0 - 40 °C
MAC address table	16000 entries
Power connector	AC-in jack
SFP module slots quantity	2
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	24
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3az, IEEE 802.3x
Virtual LAN features	Private VLAN, Voice VLAN, Port-based VLAN
DHCP features	DHCP client

Weight and Dimensions

Depth	169 mm
Width	328 mm
Height	43 mm
Weight	1620 g