NETGEAR GS324T User Manual

S350 Series 24-Port (PoE+) and 48-Port Gigabit Ethernet Smart Managed Pro Switches
Manage Device Security User Manual287
You can either select the enter the port range yourself or select one of the
following protocols from the menu:
• The destination IP TCP port range names are Domain, Echo, FTP, FTP data,
www-http, SMTP, Telnet, POP2, POP3, and bgp.
• The destination IP UDP port range names are Domain, Echo, SNMP, NTP,
RIP, Time,
Who, and TFTP.
Each of these values translates into its equivalent port number, which is used as
both the start and end of the port range.
Select Other from the menu to enter a port number. If you select Other from the
menu but leave the field blank, it means any.
The wildcard mask determines which bits are used and which bits are ignored. A
wildcard mask of 0.0.0.0 indicates that none of the bits are important. A wildcard
of 255.255.255.255 indicates that all of the bits are important.
• IGMP Type. If your selection from the Protocol Type
menu is IGMP and you specify
the IGMP type, the IP ACL rule matches the specified IGMP message type. The
range is from 0 to 255. If this field is left empty, it means any.
• ICMP. If your selection from the Protocol Type menu is
ICMP, you can select either
the Type or Message radio button:
- Type. If you select the Type
radio button, note the following:
• The Type and Code fields are enabled only if the protocol is ICMP. Use these
fields to specify a match condition for ICMP packets:
• If you specify information in the Type
field, the IP ACL rule matches the
specified ICMP message type. The type number can be from 0 to 255.
• If you specify information in the Code field, the IP ACL rule matches the
specified ICMP message code.
The code can be from 0 to 255.
• If these fields are left empty, it means
any.
- Message. If you select the Message radio button, from the menu, select the type
of the ICMP message to match with the selected IP ACL rule. Specifying a type of
message implies that both the ICMP type and ICMP code are specified.
The
ICMP message is decoded into the corresponding ICMP type and ICMP code
within the ICMP type.
The IPv4 ICMP message types are Echo, echo-reply, host-redirect,
mobile-redirect, net-redirect, net-unreachable, redirect, packet-too-big,
port-unreachable, source-quench, router-solicitation, router-advertisement,
TTL-exceeded, time-exceeded, and unreachable.
• Fragments. Either select the Enable radio button to allow initial fragments (that is,
the fragment bit is asserted) or leave the default Disable radio button selected to
prevent initial fragments from being used.
This option is not valid for rules that match L4 information such as a TCP port
number
, because that information is carried in the initial packet.
•
Service Type. Select a service type match condition for the extended IP ACL rule.

NETGEAR GS324T Specifications

General

Switch type	Managed
Switch layer	L2/L3/L4
ARP inspection	Yes
Master (outer) case width	270 mm
Master (outer) case height	271 mm
Master (outer) case length	481 mm
Master (outer) case weight	8850 g
Harmonized System (HS) code	85176990
Quantity per master (outer) case	3 pc(s)
Package type	Box
Package depth	465 mm
Package width	229 mm
Package height	79 mm
Package weight	2710 g
Cables included	AC
Stackable	-
Product color	Black
Input current	5 A
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	13.5 W
Operating temperature (T-T)	0 - 40 °C
MAC address table	16000 entries
Power connector	AC-in jack
SFP module slots quantity	2
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	24
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3az, IEEE 802.3x
Virtual LAN features	Private VLAN, Voice VLAN, Port-based VLAN
DHCP features	DHCP client

Weight and Dimensions

Depth	169 mm
Width	328 mm
Height	43 mm
Weight	1620 g