Omron V1000 - Page 400

Digital Operator Display Selection........................................ 329
DIP Switch S1..................................................................57
Down 2 Command........................................................... 316
Down Command ............................................................. 315
Drive/kVA Selection ........................................................ 329
Drive Baseblock ............................................................. 228
Drive Capacity Setting Fault ............................................... 247
Drive Capacity Signal Fault .......................................... 228, 232
Drive Cooling Fans............................................................24
Drive Disabled ......................................................... 228, 242
Drive Does Not Allow Selection of Rotational Auto-Tuning ......... 255
Drive Enable............................................................ 316, 318
Drive Mode ................................................................ 70, 71
Drive Models and Types......................................................32
Drive Mode Unit Monitor Selection ...................................... 329
Drive Node Address......................................................... 319
Drive Operation Status at Previous Fault................................. 334
Drive Overheat ............................................................... 228
Drive Overheat Alarm (oH2)............................................... 315
Drive Overheat Warning.................................................... 244
Drive Overload......................................................... 228, 236
Drive Ready .................................................................. 317
Drive Status................................................................... 333
Drive Transmit Wait Time ................................................. 320
Drive Unit Setting Error .................................................... 229
Drive Watt Loss Data ....................................................... 294
During Baseblock............................................................ 317
During Fast-stop ............................................................. 318
During Run ................................................................... 317
During Run 2, Motor Switch Command Input........................... 228
During Torque Limit ........................................................ 318
Dwell Frequency at Stop.................................................... 303
Dwell Function............................................................... 225
Dwell Reference at Start .................................................... 303
Dwell Time at Start.......................................................... 303
Dwell Time at Stop .......................................................... 303
Dynamic Braking Resistor.................................................. 228
Dynamic Braking Transistor ......................................... 228, 238
E
E1-03 ........................................................ 254, 255, 308, 339
E1-03 V/f Pattern Settings.................................................. 339
E1-03 V/f Pattern Settings for Drive Capacity: 200/400 V ............ 339
E1-04 ............................................ 249, 255, 256, 258, 259, 339
E1-04 through E1-10 ...................................... 234, 235, 236, 244
E1-06 .............................................................. 236, 256, 339
E1-07 .................................................................... 249, 339
E1-08 .................................................. 224, 225, 235, 236, 254
E1-08 and E1-10 ............................................................. 244
E1-09 .................................................. 249, 253, 254, 259, 339
E1-10 ............................................ 224, 225, 235, 236, 254, 256
E1 V/f Pattern Characteristics.............................................. 308
E2-01 .................................................. 224, 235, 236, 309, 390
E2-02 .................................................................... 224, 309
E2-03 .............................................................. 224, 250, 309
E2-04 .......................................................................... 309
E2-05 .......................................................................... 309
E2-06 .......................................................................... 309
E2-07 .................................................................... 250, 309
E2-08 .................................................................... 250, 309
E2-09 .......................................................................... 309
E2-10 .......................................................................... 309
E2-11 .......................................................................... 309
E2-12
.......................................................................... 309
E2 Motor Parameters........................................................ 309
E3-01 .......................................................................... 309
E3-04 through E3-10 ........................................................ 234
E3-06 .......................................................................... 249
E3 Motor 2 V/f Characteristics ............................................ 309
E4-01 .......................................................................... 310
E4-02 .......................................................................... 310
E4-03 .......................................................................... 310
E4-04 .......................................................................... 310
E4-05 .......................................................................... 310
E4-06 .......................................................................... 310
E4-07 .......................................................................... 310
E4-08 .......................................................................... 310
E4-09 .......................................................................... 310
E4-10 .......................................................................... 310
E4-11 .......................................................................... 310
E4-12 .......................................................................... 310
E4-15 .......................................................................... 310
E4 Motor 2 Parameters...................................................... 310
E5-01 .............................................................. 234, 248, 258
E5-03 .......................................................................... 248
E5-09 .......................................................................... 248
E5-24 .......................................................................... 248
E5 PM Motor Parameters................................................... 311
EEPROM Data Error........................................................ 231
EEPROM Serial Communication Fault................................... 231
EEPROM Write Error....................................................... 233
EF ........................................................................ 228, 242
EF0 ................................................................ 228, 232, 242
EF1 ...................................................................... 232, 242
EF2 ...................................................................... 232, 242
EF3 ...................................................................... 232, 242
EF4 ...................................................................... 232, 242
EF5 ...................................................................... 232, 242
EF6 ...................................................................... 232, 242
EMC Guidelines ............................................................. 382
End1 ..................................................................... 229, 250
End2 ..................................................................... 229, 250
End3 ..................................................................... 229, 250
Energy Saving Coefficient Value.......................................... 303
Energy Saving Control Filter Time Constant ............................ 303
Energy Saving Control Selection .......................................... 303
Energy Saving Gain ......................................................... 303
Er-01..................................................................... 229, 250
Er-02..................................................................... 229, 250
Er-03..................................................................... 229, 250
Er-04..................................................................... 229, 250
Er-05..................................................................... 229, 251
Er-08..................................................................... 229, 251
Er-09..................................................................... 229, 251
Er-11..................................................................... 229, 251
Er-12..................................................................... 229, 251
Err.............................................................................. 233
Excessive Motor Oscillation and Erratic Rotation ...................... 257
Excessive PID Feedback........................................ 228, 233, 243
Excessive Speed Deviation (for Simple V/f with PG) .................. 228
Excessive V/f Setting.................................................. 229, 250
External Digital Operator Connection Fault ............................. 237
External Fault .......................................................... 233, 243
External Fault (user selection possible)................................... 316
External Search Command 1 ............................................... 316
Index
SIEP C710606 20 OYMC AC Drive - V1000 User Manual
399
7/16/2008-13:23