External Search Command 2 ............................................... 316
Drive Motor Overload Protection......................................... 389
Drive Short-Circuit Rating................................................. 389
European Standards...........................................................16
Low Voltage Wiring........................................................ 389
UL Standards ..................................................................16
F
F1-02 .......................................................................... 312
F1-03 .......................................................................... 312
F1-04 .......................................................................... 312
F1-08 .............................................................. 237, 245, 312
F1-08 and F1-09 ............................................................. 237
F1-09 .................................................................... 245, 312
F1-10 .............................................................. 232, 242, 312
F1-10 and F1-11 ............................................................. 232
F1-11 .............................................................. 232, 242, 312
F1-14 .............................................................. 238, 245, 312
F1 Simple PG V/f Parameters.............................................. 312
F1 V/f Control with Simple PG Feedback - PG Setup Parameters.... 312
F6-03 .................................................................... 232, 242
F6 and F7 Serial Communications Option Card Settings .............. 312
Fast-stop (N.C.) .............................................................. 315
Fast-Stop (N.O.) ............................................................. 315
Fast-stop Time ............................................................... 304
Fault ........................................................................... 317
Fault Causes and Solutions ................................................. 230
Fault Detection ............................................................... 230
Fault Displays ................................................................ 230
Fault History.................................................................. 252
Fault Reset .................................................................... 315
Fault Reset Example......................................................... 227
Fault Reset Interval Time................................................... 323
Fault Reset Operation Selection ........................................... 323
Faults .......................................................................... 227
Fault Trace Example ........................................................ 252
FbH ................................................................ 228, 233, 243
FbL ................................................................ 228, 233, 243
FDBs Connection Parameters.............................................. 330
Feedback Detection Control Time Constant 2 ........................... 255
FLASH memory error....................................................... 232
FLASH Memory Fault ................................................ 227, 231
Forward/Reverse Run Command Input Error............................ 242
Forward Jog .................................................................. 315
Forward Regenerative Torque Limit ...................................... 325
Forward Run Command (2-Wire sequence) ............................. 316
Forward Torque Limit....................................................... 325
Fref/Fout Agree 1............................................................ 317
Fref/Fout Agree 2............................................................ 318
Fref/Fset Agree 1 ............................................................ 317
Fref/Fset Agree 2 ............................................................ 318
Frequency (FOUT) Detection 1............................................ 317
Frequency (FOUT) Detection 2............................................ 317
Frequency Bias (A1) ........................................................ 319
Frequency Detection 3 ...................................................... 318
Frequency Detection 4 ...................................................... 318
Frequency Gain .............................................................. 319
Frequency Reduction Rate during oH Pre-Alarm ....................... 326
Frequency Reference ........................................................ 332
Frequency Reference (Current) Terminal A2 Input Bias............... 319
Frequency Reference 1...................................................... 306
Frequency Reference 10 .................................................... 306
Frequency Reference 11
.................................................... 307
Frequency Reference 12 .................................................... 307
Frequency Reference 13 .................................................... 307
Frequency Reference 14 .................................................... 307
Frequency Reference 15 .................................................... 307
Frequency Reference 16 .................................................... 307
Frequency Reference 2.......................................... 257, 300, 306
Frequency Reference 3...................................................... 306
Frequency Reference 4...................................................... 306
Frequency Reference 5...................................................... 306
Frequency Reference 6...................................................... 306
Frequency Reference 7...................................................... 306
Frequency Reference 8...................................................... 306
Frequency Reference 9...................................................... 306
Frequency Reference Accel/Decel (Up/Down 2)........................ 307
Frequency Reference at Previous Fault ................................... 334
Frequency Reference at Reference Loss.................................. 323
Frequency Reference Bias (Up/Down 2) ........................... 307, 337
Frequency Reference Bias Operation Mode Selection (Up/Down 2)
.................................................................................. 307
Frequency Reference Bias Step (Up/Down 2) ........................... 307
Frequency Reference Hold Function Selection .......................... 307
Frequency Reference Loss Detection Selection ......................... 323
Frequency Reference Lower Limit (Up/Down 2) ....................... 308
Frequency Reference Selection ............................................ 300
Frequency Reference Selection 1.......................................... 253
Frequency Reference Setting / Decimal Display ........................ 329
Frequency Reference Setting and User-Set Display .................... 329
Frequency Reference Setting Method Selection......................... 329
Frequency Reference Upper Limit ........................................ 307
Frequency Reference Upper Limit (Up/Down 2) ....................... 308
Frequency Reference Wiring.................................................54
FWD/REV Command (2-wire sequence 2) .............................. 316
FWD/REV Torque Limit ................................................... 319
FWD Torque Limit .......................................................... 319
G
General Safety Information...................................................13
GF........................................................................ 228, 233
Ground Fault ........................................................... 228, 233
Ground Fault Interrupter Activates When Drive is Running .......... 260
Ground Wiring .................................................................48
H
H1-01.......................................................................... 315
H1-01 through to H1-06 .................................................... 247
H1-02.......................................................................... 315
H1-03.......................................................................... 315
H1-04.......................................................................... 315
H1-05......................................................................41, 315
H1-06.......................................................................... 315
H1 Multi-Function Digital Input........................................... 315
H1 Multi-Function Digital Input Selections.............................. 315
H2-01.................................................................... 257, 317
H2-01 to H2-03 .............................................................. 241
H2-02.......................................................................... 317
H2-03.......................................................................... 317
H2-06.......................................................................... 317
H2 Multi-Function Digital Outputs ....................................... 317
H2 Multi-Function Digital Output Settings .............................. 317
H3-01.......................................................................... 318
H3-02............................................ 235, 255, 256, 258, 318, 319
H3-02 and H3-10 ............................................................ 248
Index
400
SIEP C710606 20 OYMC AC Drive - V1000 User Manual
7/16/2008-13:23
To Next Page
Loading...
