Operating Instructions
CLV 480 Bar Code Scanner
Contents
I-6 © SICK AG · Division Auto Ident · Germany · All rights reserved 8 010 080/O824/10-02-2005
4.5 Dismantling the device........................................................................................................ 4-13
5 Electrical installation ................................................................................................. 5-1
5.1 Installation sequence............................................................................................................. 5-1
5.1.1 SICK Connection Modules (overview)......................................................................5-1
5.2 Electrical connections and cables .....................................................................................5-2
5.2.1 Wire cross-sections ..........................................................................................................5-2
5.2.2 Prefabricated cables (overview) ..................................................................................5-2
5.2.3 Connections/cables for the AMV/S 60 Connection Module............................ 5-3
5.2.4 Connections/cables for the Bus Connection Modules
BMV 10 and BMS 20 ......................................................................................................5-4
5.2.5 Connections/cables for the external parameter memory
(connection to AMV/S or BMV 10/BMS 20)..........................................................5-5
5.2.6 Connections/cables for the IP 65 connector cover
(connection to AMV 100/200 or BMV 10).............................................................5-5
5.3 Connector pin assignment....................................................................................................5-7
5.3.1 Terminals on the CLV.......................................................................................................5-7
5.3.2 External parameter memory no. 2 020 307/no. 2 021 689/
no. 2 027 543 or connector cover no. 2 021 298/
no. 2 021 267 (optional accessories)......................................................................5-8
5.4 Preparations for electrical installation...............................................................................5-9
5.4.1 Requirements for the host interface..........................................................................5-9
5.4.2 Supply voltage ....................................................................................................................5-9
5.4.3 Non-SICK Power supply unit/connections without the
Connection Module........................................................................................................5-10
5.5 Electrical installation procedure....................................................................................... 5-14
5.5.1 Individual steps................................................................................................................ 5-14
5.5.2 Tools....................................................................................................................................5-14
5.5.3 Connecting the supply voltage ..................................................................................5-14
5.5.4 Connecting the host interface ................................................................................... 5-15
5.5.5 Connecting the CAN interface ................................................................................... 5-16
5.5.6 Connecting the PC..........................................................................................................5-16
5.5.7 Connecting the "Sensor" switching input..............................................................5-17
5.5.8 Connecting the "IN 0" to "IN 4" switching inputs...............................................5-18
5.5.9 Connecting the "Result 1" to "Result 4" switching outputs........................... 5-21
6 Operation ....................................................................................................................... 6-1
6.1 Overview of steps for starting up the CLV ......................................................................6-1
6.2 Default settings.........................................................................................................................6-1
6.2.1 Default settings of the line scanner CLV 480 (all variants)...............................6-2
6.2.2 Default settings of the line scanner with oscillating mirror
CLV 480 (all variants) ......................................................................................................6-2
6.3 Quick start ...................................................................................................................................6-3
6.3.1 Starting up the CLV with the factory default settings...........................................6-3
6.4 Configuring (parameterization) the CLV...........................................................................6-5
6.4.1 Configuring the CLV via the user interface of CLV-Setup...................................6-5
6.4.2 Function of the tabs in CLV-Setup (overview) ........................................................6-7
6.4.3 Guide to parameterization menu.................................................................................6-9
6.5 Operating modes and outputing the reading result ................................................. 6-25
6.5.1 Reading mode (standard operating mode)..........................................................6-25
6.5.2 Percentage evaluation..................................................................................................6-28
6.5.3 Adjusting mode................................................................................................................ 6-30
6.5.4 Show CP-limits .................................................................................................................6-30
6.5.5 I/O monitor in increment trigger................................................................................6-31
6.5.6 Displaying and editing operating data .................................................................... 6-36
6.5.7 Reading diagnosis ..........................................................................................................6-36
6.5.8 Monitor Host Interface..................................................................................................6-37
6.5.9 Auxiliary input.................................................................................................................... 6-39
6.5.10 Code statistics for RDT 400....................................................................................... 6-39
To Next Page
Loading...
Need help?
General
