Contents
xvii
ET 200X Distributed I/O Device
EWA 4NEB 780601602-06
Tables
1-1 Features of the ET200X-DESINA and ET200X-ECOFAST 1-8. . . . . . . . . . .
1-2 Topics of the manuals in the ET 200X manual package 1-18. . . . . . . . . . . . . .
1-3 Separate manuals for ET 200X components 1-19. . . . . . . . . . . . . . . . . . . . . . . .
2-1 Brief overview of the different basic modules 2-2. . . . . . . . . . . . . . . . . . . . . . .
2-2 Restrictions imposed on the maximum configuration by the power input 2-14
3-1 DIN rails for installing an ET 200X 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2 Outer diameters of pneumatic tubing 3-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1 Order of steps for wiring the ET 200X 4-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2 Cable types 4-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3 Technical specifications of the 5-core cable 4-13. . . . . . . . . . . . . . . . . . . . . . . . .
4-4 Wiring rules for connectors 4-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5 Pinout of the coupler plug for digital inputs 4-23. . . . . . . . . . . . . . . . . . . . . . . . . .
4-6 Pinout of the coupler plug for digital inputs (DESINA) 4-24. . . . . . . . . . . . . . . . .
4-7 Pinout of the coupler plug for digital inputs (standard) 4-25. . . . . . . . . . . . . . . .
4-8 Pinout of the coupler plug for digital outputs 4-25. . . . . . . . . . . . . . . . . . . . . . . . .
4-9 Pinout of the coupler plug for digital outputs (DESINA) 4-26. . . . . . . . . . . . . . .
4-10 Pinout of the coupler plug for digital outputs (standard) 4-27. . . . . . . . . . . . . . .
4-11 Pinout of the coupler plugs for digital inputs when a Y connector is used 4-28
4-12 Pinout of the coupler plugs for digital outputs when a Y connector is used 4-29
4-13 Switching the output voltage to the bus segment of the ET 200X 4-41. . . . . . .
4-14 Switching over the short circuit response 4-42. . . . . . . . . . . . . . . . . . . . . . . . . . .
4-15 Switching over current limiting 4-43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1 Display and analysis of the parameters for the DESINA functional input 5-2.
5-2 Software requirements for commissioning an ET 200X (except DESINA) 5-8
5-3 Software requirements for commissioning an ET 200X-DESINA 5-9. . . . . . .
5-4 Integrating the DDB file in the configuration software 5-10. . . . . . . . . . . . . . . . .
5-5 Requirements for commissioning the DP slave 5-11. . . . . . . . . . . . . . . . . . . . . .
5-6 Order of steps for commissioning the DP slave 5-12. . . . . . . . . . . . . . . . . . . . .
5-7 Status and error display by means of LEDs on the BM 141 and
BM 142 basic modules 5-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-8 Status and fault displays using LEDs on the basic modules 5-16. . . . . . . . . . .
5-9 Status and error displays by means of LEDs on SITOP power 5-20. . . . . . . .
5-10 Diagnostics messages of the EM 142 DO 4 x DC 24V/2A and
PM 148 DO 4 x DC 24V/2A 5-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-11 Diagnostic messages for modules with AI 5-22. . . . . . . . . . . . . . . . . . . . . . . . . . .
5-12 Diagnostic messages for modules with AO 5-22. . . . . . . . . . . . . . . . . . . . . . . . . .
5-13 Diagnostic messages – causes and remedial action 5-24. . . . . . . . . . . . . . . . . .
5-14 Events that can trigger diagnostic interrupt 5-27. . . . . . . . . . . . . . . . . . . . . . . . . .
5-15 Reading out the diagnosis of ET 200X with STEP 7 and STEP 5 5-31. . . . . .
5-16 Structure of station status 1 (Byte 0) ET 200X 5-36. . . . . . . . . . . . . . . . . . . . . . .
5-17 Structure of station status 2 (Byte 1) ET 200X 5-37. . . . . . . . . . . . . . . . . . . . . .
5-18 Structure of Station Status 3 (Byte 2) ET 200X 5-37. . . . . . . . . . . . . . . . . . . . .
5-19 Structure of the manufacturer ID (Byte 4, 5) ET 200X 5-38. . . . . . . . . . . . . . . .
5-20 Channel-specific error messages to PROFIBUS standard 5-44. . . . . . . . . . . .
5-21 Channel-specific error messages – manufacturer-specific 5-45. . . . . . . . . . . . .
5-22 Bytes x+4 to x+10 in the diagnosis of ET 200X 5-55. . . . . . . . . . . . . . . . . . . . . .
5-23 Bytes x+4 to x+7 in the diagnosis of ET 200X 5-56. . . . . . . . . . . . . . . . . . . . . . .
7-1 Pinout of the sockets for 8-channel digital inputs 7-3. . . . . . . . . . . . . . . . . . . .
7-2 Parameters of the BM 141 DI 8 DC 24V 7-5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3 Pinout of sockets X1 to X8 for digital inputs 7-8. . . . . . . . . . . . . . . . . . . . . . . . .
7-4 Parameters of the BM 141 DI 8 DC 24V ECOFAST 7-10. . . . . . . . . . . . . . . . . .
7-5 Pinout of sockets X1 to X8 for digital inputs 7-13. . . . . . . . . . . . . . . . . . . . . . . . .
7-6 Parameters of the BM 141 DI 8 DC 24V ECOFAST DIAG 7-15. . . . . . . . . . . .
7-7 Parameters of the BM 141 DI 8 DC 24V ECOFAST DIAG
To Next Page
Loading...
