YASKAWA Z1000 User Manual

No. Name
User
Setting
b5-30 PI Feedback Offset
b5-34
PI Output Lower Limit
b5-35
PI Input Limit
b5-36 PI Feedback High Detection Level
b5-37 PI Feedback High Detection Time
b5-38 PI Setpoint User Display
b5-39 PI Setpoint Display Digits
b5-40 Frequency Reference Monitor Content during PI
b5-41 PI Unit Selection
b5-42
PI Output Monitor Calculation Method
b5-43
PI Output 2 Monitor Max Upper 4 Digits
b5-44
PI Output 2 Monitor Max Lower 4 Digits
b5-45
PI Output 2 Monitor Minimum
b5-46 PI Setpoint Monitor Unit Selection
b5-47 Reverse Operation Selection 2 by PI Output
b5-48 PI 4-20 mA Feedback Loss Detection Level
b5-49 PI 4-20 mA Feedback Loss Detection Time
b8-01 Energy Saving Control Selection
b8-04 Energy Saving Coefficient Value
b8-05 Power Detection Filter Time
b8-06 Search Operation Voltage Limit
C1-01
Acceleration Time 1
C1-02
Deceleration Time 1
C1-03
Acceleration Time 2
C1-04
Deceleration Time 2
C1-09 Fast-Stop Time
C1-11 Accel/Decel Time Switching Frequency
C2-01 S-Curve Characteristic at Accel Start
C2-02 S-Curve Characteristic at Accel End
C4-01
Torque Compensation Gain
C4-02
Torque Compensation Primary Delay Time
C6-02 Carrier Frequency Selection
C6-03 Carrier Frequency Upper Limit
C6-04 Carrier Frequency Lower Limit
C6-05 Carrier Frequency Proportional Gain
No. Name
User
Setting
d1-01
Frequency Reference 1
d1-02
Frequency Reference 2
d1-03
Frequency Reference 3
d1-04
Frequency Reference 4
d1-16
HAND Frequency Reference 1
d1-17
Jog Frequency Reference
d2-01 Frequency Reference Upper Limit
d2-02 Frequency Reference Lower Limit
d2-03 Master Speed Reference Lower Limit
d3-01 Jump Frequency 1
d3-02 Jump Frequency 2
d3-03 Jump Frequency 3
d3-04 Jump Frequency Width
d4-01 Frequency Reference Hold Function Selection
d4-10 Up/Down Frequency Reference Limit Selection
d6-01 Field Weakening Level
d6-02 Field Weakening Frequency Limit
d7-01
Offset Frequency 1
d7-02
Offset Frequency 2
d7-03
Offset Frequency 3
E1-01 Input Voltage Setting
E1-03 V/f Pattern Selection
E1-04 Maximum Output Frequency
E1-05 Maximum Voltage
E1-06 Base Frequency
E1-07 Middle Output Frequency
E1-08 Middle Output Frequency Voltage
E1-09 Minimum Output Frequency
E1-10 Minimum Output Frequency Voltage
E1-11 Middle Output Frequency 2
E1-12 Middle Output Frequency Voltage 2
E1-13 Base Voltage
E2-01 Motor Rated Current
E2-02 Motor Rated Slip
E2-03 Motor No-Load Current
E2-04 Number of Motor Poles
E2-05 Motor Line-to-Line Resistance
E2-10 Motor Iron Loss for Torque Compensation
E2-11 Motor Rated Power
E5-02 Motor Rated Power
E.3 User Setting Table
382
YASKAWA ELECTRIC TOEP C710616 45F YASKAWA AC Drive – Z1000 User Manual

YASKAWA Z1000 Specifications

General

Model	Z1000
Category	Controller
Humidity	95% RH or less (non-condensing)
Control Method	V/F Control
Frequency Range	400 Hz
Protection	Overcurrent, Overvoltage, Undervoltage, Overheat
Communication Options	Modbus
Operating Temperature	-10 to 50°C
Storage Temperature	-20 to 60°C
Altitude	Up to 1000 meters without derating
Cooling Method	Forced Air
Enclosure Rating	IP20
Voltage Class	200V, 400V