Cisco Catalyst 3750 User Manual

2-114
Catalyst 3750 Switch Command Reference
OL-8552-07
Chapter 2 Catalyst 3750 Switch Cisco IOS Commands
deny (IPv6 access-list configuration)
Syntax Description protocol Name or number of an Internet protocol. It can be one of the keywords
ahp, esp, icmp, ipv6, pcp, sctp, tcp, or udp, or an integer in the range
from 0
to 255 representing an IPv6 protocol number.
source-ipv6-prefix/prefix-
length
The source IPv6 network or class of networks about which to set deny
conditions.
This argument must be in the form documented in RFC 2373 where the
address is specified in hexadecimal using 16-bit values between colons.
Note Although the CLI help shows a prefix-length range of /0 to /128,
the switch supports IPv6 address-matching only for prefixes in the
range of /0 to /64 and extended universal identifier (EUI)-based
/128 prefixes for aggregatable global unicast and link-local host
addresses.
any An abbreviation for the IPv6 prefix ::/0.
host source-ipv6-address The source IPv6 host address for which to set deny conditions.
This source-ipv6-address argument must be in the form documented in
RFC 2373 where the address is specified in hexadecimal using 16-bit
values between colons.
operator [port-number] (Optional) Specify an operator that compares the source or destination
ports of the specified protocol. Operators are lt (less than), gt (greater
than), eq (equal), neq (not equal), and range (inclusive range).
If the operator is positioned after the source-ipv6-prefix/prefix-length
argument, it must match the source port.
If the operator is positioned after the destination-ipv6-prefix/prefix-length
argument, it must match the destination port.
The range operator requires two port numbers. All other operators require
one port number.
The optional port-number argument is a decimal number or the name of a
TCP or a UDP port. A port number is a number from 0 to 65535. TCP port
names can be used only when filtering TCP. UDP port names can be used
only when filtering UDP.
destination-ipv6-prefix/
prefix-length
The destination IPv6 network or class of networks for which to set deny
conditions.
This argument must be in the form documented in RFC 2373 where the
address is specified in hexadecimal using 16-bit values between colons.
Note Although the CLI help shows a prefix-length range of /0 to /128,
the switch supports IPv6 address-matching only for prefixes in the
range of /0 to /64 and EUI-based /128 prefixes for aggregatable
global unicast and link-local host addresses.
host
destination-ipv6-address
The destination IPv6 host address for which to set deny conditions.
This destination-ipv6-address argument must be in the form documented
in RFC 2373 where the address is specified in hexadecimal using 16-bit
values between colons.
dscp value (Optional) Match a differentiated services code point value against the
traffic class value in the Traffic Class field of each IPv6 packet header. The
acceptable range is from 0 to 63.

Cisco Catalyst 3750 Specifications

General

Device Type	Switch
Switching Capacity	32 Gbps
Forwarding Rate	38.7 Mpps
Stacking Bandwidth	32 Gbps
RAM	128 MB
Jumbo Frame Support	Yes
Switch Type	Managed
Model	Catalyst 3750 Series
Uplink Interfaces	SFP
Form Factor	Rack-mountable
MAC Address Table Size	12, 000 entries
Routing Protocol	RIP, OSPF, EIGRP
Remote Management Protocol	SNMP, Telnet, HTTP
Features	Layer 3 switching, Layer 2 switching, auto-negotiation, BOOTP support, ARP support, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, traffic shaping, MAC address filtering, Quality of Service (QoS), Jumbo Frames support, MLD snooping, Dynamic ARP Inspection (DAI), Cisco EnergyWise technology
Power over Ethernet (PoE)	PoE
Operating Temperature	-5 - 45 °C
Operating Humidity	10% to 85% non-condensing