EasyManuals Logo

Cisco Catalyst 3750 User Manual

Cisco Catalyst 3750
1154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #624 background imageLoading...
Page #624 background image
2-594
Catalyst 3750 Switch Command Reference
OL-8552-07
Chapter 2 Catalyst 3750 Switch Cisco IOS Commands
show ip igmp snooping
show ip igmp snooping
Use the show ip igmp snooping user EXEC command to display the Internet Group Management
Protocol (IGMP) snooping configuration of the switch or the VLAN.
show ip igmp snooping [groups | mrouter | querier] [vlan vlan-id] [ | {begin | exclude | include}
expression]
Syntax Description
Command Modes User EXEC
Command History
Usage Guidelines Use this command to display snooping configuration for the switch or for a specific VLAN.
VLAN IDs 1002 to 1005 are reserved for Token Ring and FDDI VLANs and cannot be used in IGMP
snooping.
Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output
do not appear, but the lines that contain Output appear.
Examples This is an example of output from the show ip igmp snooping vlan 1 command. It shows snooping
characteristics for a specific VLAN.
Switch# show ip igmp snooping vlan 1
Global IGMP Snooping configuration:
-----------------------------------
IGMP snooping :Enabled
IGMPv3 snooping (minimal) :Enabled
Report suppression :Enabled
TCN solicit query :Disabled
groups (Optional) See the show ip igmp snooping groups command.
mrouter (Optional) See the show ip igmp snooping mrouter command.
querier (Optional) See the show ip igmp snooping querier command.
vlan vlan-id (Optional) Specify a VLAN; the range is 1 to 1001 and 1006 to 4094 (available
only in privileged EXEC mode).
| begin (Optional) Display begins with the line that matches the expression.
| exclude (Optional) Display excludes lines that match the expression.
| include (Optional) Display includes lines that match the specified expression.
expression Expression in the output to use as a reference point.
Release Modification
12.1(11)AX This command was introduced.
12.1(19)EA1 The querier keyword was added.
12.2(18)SE The groups keyword was added. The show ip igmp snooping groups
command replaced the show ip igmp snooping multicast command.

Table of Contents

Other manuals for Cisco Catalyst 3750

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 3750 and is the answer not in the manual?

Cisco Catalyst 3750 Specifications

General IconGeneral
Device TypeSwitch
Switching Capacity32 Gbps
Forwarding Rate38.7 Mpps
Stacking Bandwidth32 Gbps
RAM128 MB
Jumbo Frame SupportYes
Switch TypeManaged
ModelCatalyst 3750 Series
Uplink InterfacesSFP
Form FactorRack-mountable
MAC Address Table Size12, 000 entries
Routing ProtocolRIP, OSPF, EIGRP
Remote Management ProtocolSNMP, Telnet, HTTP
FeaturesLayer 3 switching, Layer 2 switching, auto-negotiation, BOOTP support, ARP support, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, traffic shaping, MAC address filtering, Quality of Service (QoS), Jumbo Frames support, MLD snooping, Dynamic ARP Inspection (DAI), Cisco EnergyWise technology
Power over Ethernet (PoE)PoE
Operating Temperature-5 - 45 °C
Operating Humidity10% to 85% non-condensing

Related product manuals