EasyManuals Logo

Cisco Catalyst 3750 User Manual

Cisco Catalyst 3750
1154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #906 background imageLoading...
Page #906 background image
2-876
Catalyst 3750 Switch Command Reference
OL-8552-07
Chapter 2 Catalyst 3750 Switch Cisco IOS Commands
trust
trust
Use the trust policy-map class configuration command to define a trust state for traffic classified
through the class policy-map configuration or the class-map global configuration command. Use the no
form of this command to return to the default setting.
trust [cos | dscp | ip-precedence]
no trust [cos | dscp | ip-precedence]
Syntax Description
Defaults The action is not trusted. If no keyword is specified when the command is entered, the default is dscp.
Command Modes Policy-map class configuration
Command History
Usage Guidelines Use this command to distinguish the quality of service (QoS) trust behavior for certain traffic from other
traffic. For example, incoming traffic with certain DSCP values can be trusted. You can configure a class
map to match and trust the DSCP values in the incoming traffic.
Trust values set with this command supersede trust values set with the mls qos trust interface
configuration command.
The trust command is mutually exclusive with set policy-map class configuration command within the
same policy map.
If you specify trust cos, QoS uses the received or default port CoS value and the CoS-to-DSCP map to
generate a DSCP value for the packet.
If you specify trust dscp, QoS uses the DSCP value from the ingress packet. For non-IP packets that are
tagged, QoS uses the received CoS value; for non-IP packets that are untagged, QoS uses the default port
CoS value. In either case, the DSCP value for the packet is derived from the CoS-to-DSCP map.
cos (Optional) Classify an ingress packet by using the packet class of service (CoS)
value. For an untagged packet, the port default CoS value is used.
dscp (Optional) Classify an ingress packet by using the packet Differentiated Services
Code Point (DSCP) values (most significant 6 bits of 8-bit service-type field). For
a non-IP packet, the packet CoS value is used if the packet is tagged. If the packet
is untagged, the default port CoS value is used to map CoS to DSCP.
ip-precedence (Optional) Classify an ingress packet by using the packet IP-precedence value
(most significant 3 bits of 8-bit service-type field). For a non-IP packet, the packet
CoS value is used if the packet is tagged. If the packet is untagged, the port default
CoS value is used to map CoS to DSCP.
Release Modification
12.1(11)AX This command was introduced.

Table of Contents

Other manuals for Cisco Catalyst 3750

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 3750 and is the answer not in the manual?

Cisco Catalyst 3750 Specifications

General IconGeneral
Device TypeSwitch
Switching Capacity32 Gbps
Forwarding Rate38.7 Mpps
Stacking Bandwidth32 Gbps
RAM128 MB
Jumbo Frame SupportYes
Switch TypeManaged
ModelCatalyst 3750 Series
Uplink InterfacesSFP
Form FactorRack-mountable
MAC Address Table Size12, 000 entries
Routing ProtocolRIP, OSPF, EIGRP
Remote Management ProtocolSNMP, Telnet, HTTP
FeaturesLayer 3 switching, Layer 2 switching, auto-negotiation, BOOTP support, ARP support, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, traffic shaping, MAC address filtering, Quality of Service (QoS), Jumbo Frames support, MLD snooping, Dynamic ARP Inspection (DAI), Cisco EnergyWise technology
Power over Ethernet (PoE)PoE
Operating Temperature-5 - 45 °C
Operating Humidity10% to 85% non-condensing

Related product manuals