EasyManuals Logo

Cisco Catalyst 3750 User Manual

Cisco Catalyst 3750
1154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #974 background imageLoading...
Page #974 background image
B-2
Catalyst 3750 Switch Command Reference
OL-8552-07
Appendix B Catalyst 3750 Switch Debug Commands
debug auto qos
debug auto qos
Use the debug auto qos privileged EXEC command to enable debugging of the automatic quality of
service (auto-QoS) feature. Use the no form of this command to disable debugging.
debug auto qos
no debug auto qos
Syntax Description This command has no keywords or arguments.
Defaults Auto-QoS debugging is disabled.
Command Modes Privileged EXEC
Command History
Usage Guidelines To display the QoS configuration that is automatically generated when auto-QoS is enabled, enable
debugging before you enable auto-QoS. You enable debugging by entering the debug auto qos
privileged EXEC command.
The undebug auto qos command is the same as the no debug auto qos command.
When you enable debugging, it is enabled only on the stack master. To enable debugging on a stack
member, you can start a session from the stack master by using the session switch-number privileged
EXEC command. Then enter the debug command at the command-line prompt of the stack member. You
also can use the remote command stack-member-number LINE privileged EXEC command on the stack
master switch to enable debugging on a member switch without first starting a session.
Examples This example shows how to display the QoS configuration that is automatically generated when
auto-QoS is enabled:
Switch# debug auto qos
AutoQoS debugging is on
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface gigabitethernet2/0/1
Switch(config-if)# auto qos voip cisco-phone
21:29:41: mls qos map cos-dscp 0 8 16 26 32 46 48 56
21:29:41: mls qos
21:29:42: no mls qos srr-queue input cos-map
21:29:42: no mls qos srr-queue output cos-map
21:29:42: mls qos srr-queue input cos-map queue 1 threshold 3 0
21:29:42: mls qos srr-queue input cos-map queue 1 threshold 2 1
Release Modification
12.1(14)EA1 This command was introduced.
12.2(18)SE The debug auto qos command replaced the debug autoqos command.

Table of Contents

Other manuals for Cisco Catalyst 3750

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 3750 and is the answer not in the manual?

Cisco Catalyst 3750 Specifications

General IconGeneral
Device TypeSwitch
Switching Capacity32 Gbps
Forwarding Rate38.7 Mpps
Stacking Bandwidth32 Gbps
RAM128 MB
Jumbo Frame SupportYes
Switch TypeManaged
ModelCatalyst 3750 Series
Uplink InterfacesSFP
Form FactorRack-mountable
MAC Address Table Size12, 000 entries
Routing ProtocolRIP, OSPF, EIGRP
Remote Management ProtocolSNMP, Telnet, HTTP
FeaturesLayer 3 switching, Layer 2 switching, auto-negotiation, BOOTP support, ARP support, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, traffic shaping, MAC address filtering, Quality of Service (QoS), Jumbo Frames support, MLD snooping, Dynamic ARP Inspection (DAI), Cisco EnergyWise technology
Power over Ethernet (PoE)PoE
Operating Temperature-5 - 45 °C
Operating Humidity10% to 85% non-condensing

Related product manuals