EasyManuals Logo

Cisco Catalyst 3750 User Manual

Cisco Catalyst 3750
1154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #780 background imageLoading...
Page #780 background image
2-750
Catalyst 3750 Switch Command Reference
OL-8552-07
Chapter 2 Catalyst 3750 Switch Cisco IOS Commands
snmp-server enable traps
Note The snmp-server enable informs global configuration command is not supported. To enable the
sending of SNMP inform notifications, use the snmp-server enable traps global configuration
command combined with the snmp-server host host-addr informs global configuration command.
Defaults The sending of SNMP traps is disabled.
Command Modes Global configuration
Command History
Usage Guidelines Specify the host (NMS) that receives the traps by using the snmp-server host global configuration
command. If no trap types are specified, all trap types are sent.
When supported, use the snmp-server enable traps command to enable sending of traps or informs.
Note Informs are not supported in SNMPv1.
To enable more than one type of trap, you must enter a separate snmp-server enable traps command
for each trap type.
To set the CPU threshold notification types and values, use the process cpu threshold type global
configuration command.
Examples This example shows how to send VTP traps to the NMS:
Switch(config)# snmp-server enable traps vtp
vlandelete (Optional) Enable SNMP VLAN-deleted traps.
vtp (Optional) Enable VLAN Trunking Protocol (VTP) traps.
Release Modification
12.1(11)AX This command was introduced.
12.1(14)EA1 The bgp, copy-config, envmon, flash, port-security, stpx, syslog,
vlancreate, and vlandelete keywords were added.
12.2(18)SE The ipmulticast, msdp, ospf [cisco-specific | errors | lsa | rate-limit |
retransmit | state-change], pim [invalid-pim-message | neighbor-change
| rp-mapping-change], and tty keywords were added.
12.2(25)SE The storm-control trap-rate value keywords were added.
12.2(37)SE The errdisable notification-rate value keywords were added.
12.2(46)SE The dot1x [ auth-fail-vlan | guest-vlan | no-auth-fail-vlan |
no-guest-vlan
] keywords were added.
12.2(50)SE The cpu threshold keywords were added.

Table of Contents

Other manuals for Cisco Catalyst 3750

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 3750 and is the answer not in the manual?

Cisco Catalyst 3750 Specifications

General IconGeneral
Device TypeSwitch
Switching Capacity32 Gbps
Forwarding Rate38.7 Mpps
Stacking Bandwidth32 Gbps
RAM128 MB
Jumbo Frame SupportYes
Switch TypeManaged
ModelCatalyst 3750 Series
Uplink InterfacesSFP
Form FactorRack-mountable
MAC Address Table Size12, 000 entries
Routing ProtocolRIP, OSPF, EIGRP
Remote Management ProtocolSNMP, Telnet, HTTP
FeaturesLayer 3 switching, Layer 2 switching, auto-negotiation, BOOTP support, ARP support, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, traffic shaping, MAC address filtering, Quality of Service (QoS), Jumbo Frames support, MLD snooping, Dynamic ARP Inspection (DAI), Cisco EnergyWise technology
Power over Ethernet (PoE)PoE
Operating Temperature-5 - 45 °C
Operating Humidity10% to 85% non-condensing

Related product manuals