D-Link DGS-3000 series - Page 88

DGS-3000 Series Layer 2 Managed Gigabit Switch CLI Reference Guide
84
<hex 0x0-0xffffffff> | offset_chunk_4 <value 0-31> <hex 0x0-0xffffffff>} | ipv6 {class |
flowlabel | source_ipv6_mask <ipv6mask> | destination_ipv6_mask <ipv6mask> | [tcp
{src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} | udp { src_port_mask
<hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} | icmp {type | code }]}]
Parameters
profile_id - Specifies the index of the access list profile.
<value 1-512> - Enter the profile ID here. This value must be between 1 and 512.
profile_name - The name of the profile must be specified. The maximum length is 32 characters.
<name 32> - Enter the profile name here.
ethernet - Specifies this is an ethernet mask.
vlan - (Optional) Specifies a VLAN mask. Only the last 12 bits of the mask will be considered.
<hex 0x0-0x0fff> - Enter the VLAN mask value here.
source_mac - (Optional) Specifies the source MAC mask.
<macmask> - Enter the source MAC address used here.
destination_mac - (Optional) Specifies the destination MAC mask.
<macmask> - Enter the destination MAC address used here.
802.1p - (Optional) Specifies the 802.1p priority tag mask.
ethernet_type - (Optional) Specifies the Ethernet type mask.
ip - Specifies this is a IPv4 mask.
vlan - (Optional) Specifies a VLAN mask. Only the last 12 bits of the mask will be considered.
<hex 0x0-0x0fff> -Enter the VLAN mask value here.
source_ip_mask - (Optional) Specifies a source IP address mask.
<netmask> - Enter the source IP address mask here.
destination_ip_mask - (Optional) Specifies a destination IP address mask.
<netmask> - Enter the destination IP address mask here.
dscp - (Optional) Specifies the DSCP mask.
icmp - (Optional) Specifies that the rule applies to ICMP traffic.
type - Specifies the type of ICMP traffic.
code - Specifies the code of ICMP traffic
igmp - (Optional) Specifies that the rule applies to IGMP traffic.
type - Specifies the type of IGMP traffic.
tcp - (Optional) Specifies that the rule applies to TCP traffic.
src_port_mask - (Optional) Specifies the TCP source port mask.
<hex 0x0-0xffff> - Enter the TCP source port mask here.
dst_port_mask - (Optional) Specifies the TCP destination port mask.
<hex 0x0-0xffff> - Enter the TCP destination port mask here.
flag_mask - (Optional) Specifies the TCP flag field mask.
all – Specifies that all the flags will be used for the TCP mask.
urg – (Optional) Specifies that the TCP flag field will be set to ‘urg’.
ack - (Optional) Specifies that the TCP flag field will be set to ‘ack’.
psh - (Optional) Specifies that the TCP flag field will be set to ‘psh’.
rst - (Optional) Specifies that the TCP flag field will be set to ‘rst’.
syn - (Optional) Specifies that the TCP flag field will be set to ‘syn’.
fin - (Optional) Specifies that the TCP flag field will be set to ‘fin’.
udp - (Optional) Specifies that the rule applies to UDP traffic.
src_port_mask - (Optional) Specifies the UDP source port mask.
<hex 0x0-0xffff> - Enter the UDP source port mask here.
dst_port_mask - (Optional) Specifies the UDP destination port mask.
<hex 0x0-0xffff> - Enter the UDP destination port mask here.
protocol_id_mask - (Optional) Specifies that the rule applies to IP protocol ID traffic.
<0x0-0xff> - Enter the protocol ID mask here.
user_define_mask - (Optional) Specifies that the rule applies to the IP protocol ID, and
that the mask option behind the IP header length is 4 bytes.
<hex 0x0-0xffffffff> - Enter a user-defined mask value here.
packet_content_mask - Specifies the packet content mask. Only one packet_content_mask
profile can be created.