Eaton Rapid Link 5 - Page 233

9 Communication
9.2 EtherNet / IP
Rapid Link 5 · RAMO5 · RASP5 05/20 MN034004EN www.eaton.com 229
P2-24 Start mode 224 R/W 0x04 0x18 0x19 1 U16 0 - 10 – 0
P2-26
Auto Reset Delay 226 R/W 0x04 0x18 0x19 1 U16 0.1 - 60.0 s 300 ≙ 30,0 s 0,5 s
P2-27
Action@Thermistorfault Motor 227 R/W 0x04 0x18 0x19 1 U16 0 - 1 – 1
P2-28
Service interval Time 228 R/W 0x04 0x18 0x19 1 U16 0 - 60000 – 0
P2-29
Reset ServiceIndicator 229 R/W 0x04 0x18 0x19 1 U16 0 - 1 – 0
P2-30
Parameter set 230 R/W 0x04 0x18 0x19 1 U16 0 - 1 – 0
P2-32
Access key level2 232 R/W 0x04 0x18 0x19 1 U16 0 - 65535 – 101
P2-33
Parameter lock 233 R/W 0x04 0x18 0x19 1 U16 0 - 1 – 0
P2-34
TCP Enable Service 234 R/W 0x04 0x18 0x19 1 U16 0 - 15 – 0
P2-36
Save parameter @24V-ext. 236 R/W 0x04 0x18 0x19 1 U16 0 - 1 – 0
P3-04
Brake
Release Delay
304 R/W 0x04 0x18 0x19 1 U16 0 - 2.50 s 25 ≙ 2,5 s 0,00 s
P3-05
Brake
Apply Delay
305 R/W 0x04 0x18 0x19 1 U16 0 - 25.00 s 2500 ≙ 25,00 s 0,00 s
P3-06
SEN I1 logic 306 R/W 0x04 0x18 0x19 1 U16 0 - 1 – 0
P3-07
SEN I2 logic 307 R/W 0x04 0x18 0x19 1 U16 0 - 1 – 0
P5-01
RS485-0 Address 501 R/W 0x04 0x18 0x19 1 U16 1 - 63 – 2
P5-02
COM Loss Timeout 502 R/W 0x04 0x18 0x19 1 U16 0.0 - 5.0 s 50 ≙ 5s 2,0 s
P5-03
Action@Communication Loss 503 R/W 0x04 0x18 0x19 1 U16 0 - 2 – 0
P5-05
NETSendPZD3 505 R/W 0x04 0x18 0x19 1 U16 0: Current
[xx.x A]
1: Power
[x.xx kW]
2: Digital
input status
– 0
P5-06
NETSendPZD4 506 R/W 0x04 0x18 0x19 1 U16 0: Current
[xx.x A]
1: Power
[x.xx kW]
2: Digital
input status
– 2
P5-07
NETReceivePZD3 507 R/W 0x04 0x18 0x19 1 U16 0 Reserved 0
P5-08
NETReceivePZD4 508 R/W 0x04 0x18 0x19 1 U16 0 Reserved 0
P5-10
Disable QuickStop 510 R/W 0x04 0x18 0x19 1 U16 0 - 1 – 0
P6-05
Action@Underload Motor 605 R/W 0x04 0x18 0x19 1 U16 0 - 1 – 0
P6-08
Change Phasesequence Motor 608 R/W 0x04 0x18 0x19 1 U16 0 - 1 Only for
RAMO5-W
0
R = “read”; W = “write”
Parameters Designation Instance Access right Object class Service code Read Service code Write Length (word) Data format Values range Scaling Default setting