Ecolab Elados EMP II E60 - Technical Specification Tables

417101438_EMPII_E60.docx
- 136 -
Rev. 11-02.14
14.3 Technical specifications "Overview tables"
Description
Pump type
V3014 V3025 00048 00043
00072
00112 00240
0,6 MPa
1 MPa
Supply voltage
230 V / 50/60 Hz ± 10 % (special voltages on request)
max. current input 115V 50/60 Hz
230V 50/60 Hz
0.12 A
0.06 A
0.20 A
0.21 A
0.09 A
0.29 / 0.33 A (0.7 A)*
0.14 / 0.16 A (0.7 A)*
Motor Power 115/230V 50/60 Hz
10.4 / 11.5 W
18.7 W
19.8 W
30 / 34.5 W (25 W)*
Fuse rating 115 V
230 V
315 mA (1A)*
Type of protection
IP 65
Breaking capacity at circuit with 24 V
Empty report output: 24 V 3 A AC/DC
stroke signal output: 24 V 0.3 A DC
Breaking capacity at circuit with 230 V
Empty report output: 230 V / 3 A AC/DC
stroke signal output: connection according to VDE is not permitted
* The values at brackets refer to types 00072, 00112, 00240 with BLDC- Motor
(visible at the voltage indication 100- 240V at identification plate)
14.3.1 General data - Standard pumps
Description
Pump type
V3014
V3025
00048
00043
00072
00112
00240
0,6 MPa
1 MPa
Pump output [l/h]* / **
1.4
2.5
4.8
4.3
7.2
11.2
24
max. metering backpressure [MPa (bar)]**
0.1 (10)
0.4 (4)
1 (10)
0.6 (6)
1 (10)
0.5 (5)
0.2 (2)
Number of strokes [1/min] at 50 Hz
122
Metering quantity/stroke [ml] 50 Hz/60 Hz
0.19
0.34
0.65
0.57
0.98
1.5
3.28
Metering accuracy [see chapter 14.4]
< ± 3%
max. conveyable viscosity [mPas]
200
Permitted ambient temperature
5-40°C
Suction height [mWs] at 100 % stroke***
2
max. pre-pressure suction sided [MPa (bar)]
0.08 (0.8)
0.05 (0.5)
0.02 (0.2)
Noise level [DBA] at 1 m distance
(acc. to DIN EN 12639/ EN ISO 9614-2)
54
Recommended minimum diameter of
suction/pressure connector [ID mm]
4 6
Weight [kg]
2
2.4
3.1
3.3
* All data relate to water at 20 °C
** At mains power frequency of 60 Hz, the delivery capacity increases by 20%, while metering backpressure decreases by 20%.
*** Suction heights with clean, moistened valves at 100% metering stroke and max. stroke frequency
14.3.2 Deviant general data - Pumps in the “Higher Pressures (HP)” version
Description
Pump type
V3014
V3025
00043
Pump output [l/h]*
1.2
2
4
max. metering backpressure [MPa (bar)]
1.6 (16)
Metering quantity/stroke [cm³]
0.16
0.27
0.55
* all data relate to water at 20 °C
14.3.3 Materials
Pump head: PVDF, optionally PP, stainless steel 1.4571
Diaphragm: PTFE-EPDM composite diaphragm
Seals: FPM (Viton B), optionally EPDM, Kalrez
Valves: PVDF, optionally PP or stainless steel 1.4571
Ball valves: Ceramic, optionally stainless steel 1.4401, PTFE
Housing: thermoplastic polyester
Colour: Blue RAL 5007
Special versions available on request.