GE Voluson P6 - Page 471

To Next Page

To Previous Page

GE HEALTHCARERAFT VOLUSON® P8 / VOLUSON® P6

DIRECTION 5459672-100, R

EVISION 6 DRAFT (JANUARY 17, 2013) PROPRIETARY SERVICE MANUAL

8-108 Section 8-44 - Replacement of CWD

4.) Unscrew Monitor Cable fix screw with "-" Driver and Disconnect all cable connectors.

Figure 8-137 Cable connectors

5.) Unscrew 9 screws and remove NEST EMI BRKT.

Figure 8-138 Nest EMI bracket

Peripherals Power Cable

Keyboard Cable

Peripherals USB Cable

SATA Cable

Speaker

Monitor Cable Fix Screw

Monitor Cable

NEST EMI BRKT

Main Page

Important Precautions2
Chapter 138
Introduction38
- Section 1-1 Overview38
- Section 1-2 Important Conventions40
- Section 1-3 Safety Considerations44
- Section 1-4 Electromagnetic Compatibility (EMC)52
- Section 1-5 Customer Assistance53
  - 1-5-1 Contact Information53
  - 1-5-2 System Manufacturer53
Chapter 256
Site Preparation56
- Section 2-1 Overview56
  - 2-1-1 Purpose of Chapter 256
- Section 2-2 General Console Requirements57
- Section 2-3 Facility Needs61
Chapter 366
Setup Instructions66
- Section 3-1 Overview66
  - 3-1-1 The Purpose of Chapter 366
- Section 3-2 Set Up Reminders66
- Section 3-3 Receiving and Unpacking the Equipment69
- Section 3-4 Preparing for Set Up73
  - 3-4-1 Verify Customer Order73
  - 3-4-2 EMI Protection73
- Section 3-5 Connection of Auxiliary Devices75
- Section 3-6 Completing the Set Up88
- Section 3-7 Printer Installation95
- Section 3-8 System Configuration119
- Section 3-9 Available Probes128
- Section 3-10 Software/Option Configuration128
- Section 3-11 Connectivity Setup129
  - 3-11-1 Connectivity Introduction129
  - 3-11-2 Wireless Network Configuration132
    - 3-11-2-1 Description of “Netgear” Configuration Parameters134
- Section 3-12 Network IP Address Configuration135
  - 3-12-1 Map Network Drive136
- Section 3-13 Connectivity Setup Worksheet138
- Section 3-14 Paperwork140
  - 3-14-1 Product Locator Installation140
  - 3-14-2 User Manual(s)140
Chapter 4142
Functional Checks142
- Section 4-1 Overview142
  - 4-1-1 Purpose of Chapter 4142
- Section 4-2 Required Equipment142
- Section 4-3 General Procedure143
- Section 4-4 Functional Checks148
- Section 4-5 Backup and Restore Database, Preset Configurations and Images175
- Section 4-6 Software Configuration Checks188
  - 4-6-1 System Setup188
  - 4-6-2 Measure Setup189
- Section 4-7 Peripheral Checks190
- Section 4-8 Site Log207
Chapter 5208
Components and Functions (Theory)208
- Section 5-1 Overview208
  - 5-1-1 Purpose of Chapter 5208
- Section 5-2 General Information209
- Section 5-3 FrontEnd Processor227
- Section 5-4 BackEnd Processor232
- Section 5-5 Internal I/O235
- Section 5-6 OPIO (User Interface)236
- Section 5-7 Monitor242
- Section 5-8 External I/O243
- Section 5-9 Peripherals244
- Section 5-10 Power Distribution245
- Section 5-11 Service Platform252
  - 5-11-1 Introduction252
  - 5-11-2 Access / Security252
- Section 5-12 Common Service Desktop (CSD)255
- Section 5-13 Service Page259
- Section 5-14 Boot Screen Functions262
  - 5-14-1 Overview262
- Section 5-15 LINUX - Voluson Maintenance System264
Chapter 6286
Service Adjustments286
- Section 6-1 Overview286
  - 6-1-1 Purpose of Chapter 6286
- Section 6-2 Regulatory286
- Section 6-3 LCD Monitor Adjustment287
- Section 6-4 Modification of Keyboard Layout288
  - 6-4-1 Setup the Voluson® P8 / Voluson® P6 Keyboard Language Layout288
Chapter 7290
Diagnostics/Troubleshooting290
- Section 7-1 Overview290
  - 7-1-1 Purpose of Chapter Voluson® P8 / Voluson® P6290
  - 7-1-2 Overview290
- Section 7-2 Collect Vital System Information291
  - 7-2-1 Request for Service (RFS)293
  - 7-2-2 Shortcuts List295
- Section 7-3 Check Points Voltages296
  - 7-3-1 How to check power296
    - 7-3-1-1 Common Power Supply (CPS)296
- Section 7-4 Screen Captures and Logs297
  - 7-4-1 Capturing a screen297
    - 7-4-1-1 How to use a Capture Filter298
    - 7-4-1-2 How to use a Screen Filter299
  - 7-4-2 Export Log’s and System Data300
    - 7-4-2-1 Export System Data (by pressing the ALT + D key)300
    - 7-4-2-2 Export Log´s and System Data (via Service Page)301
- Section 7-5 Remote Access to Service Platform302
- Section 7-6 How to install/use the Process Logger316
- Section 7-7 How to use the Auto Tester program316
- Section 7-8 How to repair Databases (*.mdb)319
- Section 7-9 Hardware Tests321
- Section 7-10 Minimum Configuration to Boot/Scan335
  - 7-10-1 Booting without using the Ultrasound Hardware335
- Section 7-11 User Interface Troubleshooting338
  - 7-11-1 Console Test338
- Section 7-12 Troubleshooting Trees, Instructions and Tech Tips340
- Section 7-13 Error Messages350
Chapter 8364
Replacement Procedures364
- Section 8-1 Overview364
  - 8-1-1 Purpose of Chapter 8364
  - 8-1-2 Returning/Shipping System, Probes and Repair Parts366
- Section 8-2 System Software - Installation Instructions367
  - 8-2-1 Manpower367
  - 8-2-2 Tools367
- Section 8-3 System Software - Installation/Upgrade Procedure371
  - 8-3-1 Introduction371
  - 8-3-2 Manpower371
  - 8-3-3 Tools371
  - 8-3-4 Preparations371
  - 8-3-5 System Software - Installation Procedure (FMI from DVD)375
- Section 8-4 Software and Functional Checks after Installation/Upgrade Procedure380
- Section 8-5 Image Settings Only - Loading Procedure381
  - 8-5-1 Introduction381
  - 8-5-2 Loading Procedure381
- Section 8-6 Full Backup (Full System Configuration) - Loading Procedure381
  - 8-6-1 Introduction381
  - 8-6-2 Loading Procedure381
- Section 8-7 Image Archive - Loading Procedure381
  - 8-7-1 Introduction381
  - 8-7-2 Loading Procedure381
- Section 8-8 Replacement or Activation of Options382
  - 8-8-1 Operation for activating Options383
    - 8-8-1-1 Operation for installing a “Demo Key” or a “Permanent Key”:383
- Section 8-9 Replacement of Monitor384
  - 8-9-1 Manpower384
  - 8-9-2 Tools384
  - 8-9-3 Remove Procedure384
  - 8-9-4 Installation Procedure385
- Section 8-10 Replacement of the MONITOR STAND ARM386
  - 8-10-1 Manpower386
  - 8-10-2 Tools386
  - 8-10-3 8-9-3 Removal Procedure386
  - 8-10-4 Installation Procedure386
- Section 8-11 Replacement of OPIO387
  - 8-11-1 Manpower387
  - 8-11-2 Tools387
  - 8-11-3 Preparations387
  - 8-11-4 Removal Procedure387
  - 8-11-5 Installation Procedure389
- Section 8-12 Replacement of the SPEAKER390
  - 8-12-1 Manpower390
  - 8-12-2 Tools390
  - 8-12-3 Preparations390
  - 8-12-4 Removal Procedure390
  - 8-12-5 Installation Procedure391
- Section 8-13 Remove the Pedestal Bottom Cover392
  - 8-13-1 Installation Procedure395
- Section 8-14 Replacement of the NEST396
  - 8-14-1 Manpower396
  - 8-14-2 Tools396
  - 8-14-3 Preparations396
  - 8-14-4 Removal Procedure396
  - 8-14-5 Installation Procedure399
- Section 8-15 Replacement of the AIR FILTER400
  - 8-15-1 Manpower400
  - 8-15-2 Tools400
  - 8-15-3 Preparations400
  - 8-15-4 Removal Procedure400
  - 8-15-5 Installation Procedure401
- Section 8-16 Replacement of the Probe Holder(KIT)402
  - 8-16-1 Manpower402
  - 8-16-2 Tools402
  - 8-16-3 Removal Procedure402
  - 8-16-4 Installation Procedure402
- Section 8-17 Replacement of SIDE COVER L ASSY403
  - 8-17-1 Manpower403
  - 8-17-2 Tools403
  - 8-17-3 Preparations403
  - 8-17-4 Removal Procedure403
  - 8-17-5 Installation Procedure404
- Section 8-18 Replacement of SIDE COVER R ASSY405
  - 8-18-1 Manpower405
  - 8-18-2 Tools405
  - 8-18-3 Preparations405
  - 8-18-4 Removal Procedure405
  - 8-18-5 Installation Procedure406
- Section 8-19 Replacement of the Trackball407
  - 8-19-1 Manpower407
  - 8-19-2 Tools407
  - 8-19-3 Preparations407
  - 8-19-4 Removal Procedure407
- Section 8-20 Replacement of the TGC BOARD410
  - 8-20-1 Manpower410
  - 8-20-2 Tools410
  - 8-20-3 Preparations410
  - 8-20-4 Removal Procedure410
  - 8-20-5 Installation Procedure411
- Section 8-21 Replacement of AN KEYBOARD ASSY412
  - 8-21-1 Manpower412
  - 8-21-2 Tools412
  - 8-21-3 Preparations412
  - 8-21-4 Removal Procedure412
  - 8-21-5 Installation Procedure413
- Section 8-22 Replacement of the Caster Cap414
  - 8-22-1 Manpower414
  - 8-22-2 Tools414
  - 8-22-3 Preparations414
  - 8-22-4 Removal Procedure414
  - 8-22-5 Installation Procedure414
- Section 8-23 Replacement of the CASTER415
  - 8-23-1 Manpower415
  - 8-23-2 Tools415
  - 8-23-3 Preparations415
  - 8-23-4 Removal Procedure415
  - 8-23-5 Installation Procedure416
- Section 8-24 Replacement of the SIDE TRAY417
  - 8-24-1 Manpower417
  - 8-24-2 Tools417
  - 8-24-3 Preparations417
  - 8-24-4 Removal Procedure417
  - 8-24-5 Installation Procedure417
- Section 8-25 Replacement of the REAR HANDLE418
  - 8-25-1 Manpower418
  - 8-25-2 Tools418
  - 8-25-3 Preparations418
  - 8-25-4 Removal Procedure418
  - 8-25-5 Installation Procedure419
- Section 8-26 Replacement of the OP COVER L,R420
  - 8-26-1 Manpower420
  - 8-26-2 Tools420
  - 8-26-3 Preparations420
  - 8-26-4 Removal Procedure420
  - 8-26-5 Installation Procedure421
- Section 8-27 Replacement of the CPS422
  - 8-27-1 Manpower422
  - 8-27-2 Tools422
  - 8-27-3 Preparations422
  - 8-27-4 Removal Procedure422
  - 8-27-5 Installation Procedure423
- Section 8-28 Replacement of the RFS424
  - 8-28-1 Manpower424
  - 8-28-2 Tools424
  - 8-28-3 Preparations424
  - 8-28-4 Removal Procedure424
  - 8-28-5 Installation Procedure425
  - 8-28-6 Serial Number - Reprogamming Procedure425
- Section 8-29 Replacement of the SOM428
  - 8-29-1 Manpower428
  - 8-29-2 Tools428
  - 8-29-3 Preparations428
  - 8-29-4 Removal Procedure428
  - 8-29-5 Installation Procedure429
- Section 8-30 Replacement of the HDD430
  - 8-30-1 Manpower430
  - 8-30-2 Tools430
  - 8-30-3 Preparations430
  - 8-30-4 Removal Procedure430
  - 8-30-5 Installation Procedure431
- Section 8-31 Replacement of the DVR432
  - 8-31-1 Manpower432
  - 8-31-2 Tools432
  - 8-31-3 Preparations432
  - 8-31-4 Removal Procedure432
  - 8-31-5 Installation Procedure433
- Section 8-32 Replacement of the BF64434
  - 8-32-1 Tools434
  - 8-32-2 Preparations434
  - 8-32-3 Removal Procedure434
  - 8-32-4 Installation Procedure435
- Section 8-33 Replacement of the PIR436
  - 8-33-1 Manpower436
  - 8-33-2 Tools436
  - 8-33-3 Preparations436
  - 8-33-4 Removal Procedure436
  - 8-33-5 Installation Procedure437
- Section 8-34 Replacement of the CSI438
  - 8-34-1 Manpower438
  - 8-34-2 Preparations438
  - 8-34-3 Removal Procedure438
  - 8-34-4 Installation Procedure439
- Section 8-35 Replacement of the CBP440
  - 8-35-1 Manpower440
  - 8-35-2 Tools440
  - 8-35-3 Preparations440
  - 8-35-4 Removal Procedure440
  - 8-35-5 Installation Procedure441
- Section 8-36 Replacement of the DVD442
  - 8-36-1 Manpower442
  - 8-36-2 Tools442
  - 8-36-3 Preparations442
  - 8-36-4 Removal Procedure442
  - 8-36-5 Installation Procedure443
- Section 8-37 Replacement of the OPIO USB Sub PWA444
  - 8-37-1 Manpower444
  - 8-37-2 Tools444
  - 8-37-3 Preparations444
  - 8-37-4 Removal Procedure444
  - 8-37-5 Installation Procedure445
- Section 8-38 Replacement of AN KEY TOP446
  - 8-38-1 Manpower446
  - 8-38-2 Tools446
  - 8-38-3 Preparations446
  - 8-38-4 Key Caps - Removal Procedure446
- Section 8-39 Replacement of FULL AN KEY447
  - 8-39-1 Manpower447
  - 8-39-2 Tools447
  - 8-39-3 Removal Procedure447
  - 8-39-4 Installation Procedure449
- Section 8-40 Replacement of the Caps for Hardkeys450
  - 8-40-1 Replacement of Circle Key Caps only450
- Section 8-41 Replacing optional Peripherals451
  - 8-41-1 Manpower451
  - 8-41-2 Tools451
  - 8-41-3 Printer Installation (BW and Color)451
    - 8-41-3-1 BW Printer: SONY UP-D897, Color Printer: SONY UP-D25MD451
    - 8-41-3-2 Color Printer Assembly458
  - 8-41-4 HORIZONTAL TV PROBE HOLDER Installation465
  - 8-41-5 VERTICAL TV PROBE HOLDER Installation466
- Section 8-42 Replacement of FAN with Cable ASSY II467
  - 8-42-1 Manpower467
  - 8-42-2 Tools467
  - 8-42-3 Preparations467
  - 8-42-4 Removal Procedure467
  - 8-42-5 Installation Procedure467
- Section 8-43 Functional Checks after FRU replacement (Debrief Guidelines)468
- Section 8-44 Replacement of CWD469
  - 8-44-1 Manpower469
  - 8-44-2 Tools469
  - 8-44-3 Preparations469
  - 8-44-4 Removal Procedure469
  - 8-44-5 Installation Procedure472
- Section 8-45 Replacement of ECG Kit assy473
  - 8-45-1 Manpower473
  - 8-45-2 Tools473
  - 8-45-3 Preparations473
  - 8-45-4 Removal Procedure473
  - 8-45-5 Installation Procedure474
Chapter 9488
Renewal Parts488
- Section 9-1 Overview488
  - 9-1-1 Purpose of Chapter 9488
- Section 9-2 List of Abbreviations489
- Section 9-3 Parts List Groups490
- Section 9-4 Plastics Covers (Front/Sides/Rear)491
- Section 9-5 LCD Monitor492
- Section 9-6 OPIO493
- Section 9-7 Nest Box Parts495
- Section 9-8 Mechanical Parts497
- Section 9-9 Options499
- Section 9-10 Optional Peripherals and Accessories500
  - 9-10-1 Printers and options500
- Section 9-11 System Manuals501
- Section 9-12 Probes502
- Section 9-13 Power Cord506
- Section 9-14 Biopsy Needle Guide508
Chapter 10512
Care & Maintenance512
- Section 10-1 Overview512
  - 10-1-1 Periodic Maintenance Inspections512
  - 10-1-2 Purpose of Chapter 10512
- Section 10-2 Why do Maintenance513
  - 10-2-1 Keeping Records513
  - 10-2-2 Quality Assurance513
- Section 10-3 Maintenance Task Schedule513
  - 10-3-1 How often should care & maintenance tasks be performed?513
- Section 10-4 Tools Required516
- Section 10-5 Tools Required518
  - 10-5-1 Special Tools, Supplies and Equipment518
    - 10-5-1-1 Specific Requirements for Care & Maintenance518
- Section 10-6 System Maintenance519
- Section 10-7 Using a Phantom (Optional)525
- Section 10-8 Electrical Safety Tests525
- Section 10-9 When There's Too Much Leakage Current...542

GE Voluson P6 - Page 471

Table of Contents

Other manuals for GE Voluson P6

Related product manuals