EasyManuals Logo

HP xw4600 User Manual

HP xw4600
176 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #41 background imageLoading...
Page #41 background image
Heading Option Description
Virtualization Technology Directed
OS Management of Embedded Security Device—Enables or disables the ability of the operating
system to control the TPM device, including turning it on and off, initializing it, and resetting it.
Reset of Embedded Security Device through OS—Enables or disables the ability of the operating
system to reset the TPM.
Setup Security
Level
Enables the administrator to selectively set the security level for each setup feature. The options
are: Setup Password and None. Browser mode must be enabled to use this option.
Power OS Power
Management
Enables or disables:
Runtime Power Management
ACPI S3 Hard Disk Reset
ACPI S3 PS 2 Mouse Wakeup
USB Wake on Device Insertion
Unique Sleep State Blink Rates
Hardware Power
Management
Enables or disables SATA Power Management
Thermal Enables you set the rate of the system fan when the processor is in idle.
Advanced** Power-On
Options
Allows you to set:
POST Mode (QuickBoot, FullBoot, or FullBoot every 1–30 days).
POST Messages (Enable or Disable).
F9 Prompt (Enable or Disable). Enabling this feature displays F9=Boot Menu during POST.
Disabling this feature prevents the text from being displayed. However, pressing the F9 key
still accesses the boot menu.
F10 Prompt (Enable or Disable)—Enabling this feature displays F10=Setup during POST.
Disabling this feature prevents the text from being displayed, but pressing F10 still accesses
the Setup screen.
F11 Prompt (Enable or Disable)—Makes the Factory Recovery option visible during POST.
Disabling this feature prevents the text from being displayed, but pressing F10 still accesses
the Setup screen. Factory Recovery Boot Support must be enabled to use this option.
F12 Prompt (Enable or Disable)—Enabling this feature displays F12=Network Service Boot
during POST. Disabling this feature prevents the text from being displayed but pressing F12
still forces the system to attempt booting from the network.
Factory Recovery Boot Support (Enable or Disable)—Recovery partition hard disk drive
(HDD) option available. Vista leaves the factory with this support in place.
Option ROM prompt* (Enable or Disable)—Enabling this feature causes the system to display
a message before loading options ROMs.
Remote Wakeup Boot Source
After Power Loss (On or Off)—Enabling this option directs the previous state to be the default.
POST Delay (in seconds) (Enable or Disable)—Enabling this feature adds a user-specified
delay to the POST process. This delay is sometimes needed for hard drives on some PCI
cards that spin up slowly (so slowly that they are not ready to boot by the time POST is
Table 3-1 Computer Setup (F10) Utility menu descriptions (continued)
ENWW Computer Setup (F10) Utility 33

Table of Contents

Other manuals for HP xw4600

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP xw4600 and is the answer not in the manual?

HP xw4600 Specifications

General IconGeneral
Tcase72.4 °C
Bus typeFSB
SteppingE0
Processor cache6 MB
Processor cores2
Processor modelE8400
System bus rate- GT/s
Processor familyIntel® Core™2 Duo
Processor seriesIntel Core 2 Duo E8000 Series
Processor socketLGA 775 (Socket T)
Processor codenameWolfdale
Processing Die size107 mm²
Processor frequency3 GHz
Processor cache typeL2
Processor lithography45 nm
Processor manufacturerIntel
Processor front side bus1333 MHz
Processor operating modes64-bit
ECC supported by processorNo
Thermal Design Power (TDP)65 W
Number of processors installed1
CPU multiplier (bus/core ratio)9
Number of Processing Die Transistors410 M
Audio systemHigh Definition Audio
Product typeWorkstation
Motherboard chipsetIntel® X38 Express
ECCYes
Internal memory2 GB
Memory clock speed800 MHz
Internal memory typeDDR2-SDRAM
Maximum internal memory8 GB
Memory layout (slots x size)2 x 1 GB
HDD speed7200 RPM
HDD capacity250 GB
HDD interfaceSATA
Optical drive typeDVD-RW
Graphics card-
Networking featuresGigabit Ethernet (10/100/1000)
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power supply475 W
Chassis typeTower
Country of originChina
Processor codeSLB9J
Processor ARK ID33910
Processor package size37.5 x 37.5 mm
On-board graphics card modelNot available
Weight and Dimensions IconWeight and Dimensions
Depth456 mm
Width168 mm
Height450 mm
Weight19000 g

Related product manuals