EasyManuals Logo

HPE FlexNetwork 5510 HI Series User Manual

HPE FlexNetwork 5510 HI Series
572 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #533 background imageLoading...
Page #533 background image
521
session establishment (multiple hop), 261
echo
IPv6 static route BFD echo mode (single hop),
378
RIP BFD configuration (bidirectional
detection/control packet mode), 60
RIP BFD configuration (single-hop echo
detection), 55
RIP BFD configuration (single-hop echo
detection/specific destination), 58
RIP BFD single-hop echo detection, 40
static routing BFD echo mode (single-hop), 13
ECMP
BGP load balancing, 267
IP routing ECMP enhanced mode, 6
IP routing ECMP route max number, 5
ISIS ECMP routes max, 145
OSPF ECMP routes max, 82
OSPFv3 ECMP route max, 420
RIP ECMP route max number, 35
RIPng ECMP route max, 394
electing
OSPF DR election configuration, 116
OSPFv3 DR election configuration, 443
enabling
BGP, 207
BGP 4-byte AS number suppression (IPv4),
264
BGP 4-byte AS number suppression (IPv6),
264
BGP MED route comparison (confederation
peers), 249
BGP MED route comparison (diff ASs), 247
BGP MED route comparison (per-AS), 247
BGP ORF capabilities, 262
BGP peer keychain authentication (IPv4), 266
BGP peer keychain authentication (IPv6), 266
BGP peer MD5 authentication (IPv4), 265
BGP peer MD5 authentication (IPv6), 265
BGP per-prefix label allocation, 279
BGP route flapping logging (IPv4), 287
BGP route flapping logging (IPv6), 287
BGP route refresh (IPv4), 271
BGP route refresh (IPv6), 271
BGP session state change logging (IPv4), 286
BGP session state change logging (IPv6), 286
BGP SNMP notification, 286
EBGP direct connections after link failure, 262
EBGP session establishment (multiple
hop)(IPv4), 261
EBGP session establishment (multiple
hop)(IPv6), 261
IP routing ECMP enhanced mode, 6
IPv6 IS-IS automatic link cost calculation, 467
IPv6 IS-IS FRR BFD, 472
IPv6 IS-IS ISPF, 469
IPv6 IS-IS MTR, 472
IPv6 IS-IS prefix suppression, 469
IPv6 route support for 64 bits+ prefixes, 8
IS-IS, 142
IS-IS automatic cost calculation, 144
IS-IS FRR BFD (control packet mode), 164
IS-IS FRR BFD (echo packet mode), 164
IS-IS interface hello packet send, 150
IS-IS ISPF, 157
IS-IS LSP flash flooding, 152
IS-IS LSP fragment extension, 153
IS-IS neighbor state change logging, 156
IS-IS PIC, 158
IS-IS PIC BFD, 158
IS-IS prefix suppression, 157
OSPF, 74
OSPF (on interface), 75
OSPF (on network), 74
OSPF ISPF, 93
OSPF PIC, 95
OSPF RFC 1583 compatibility, 91
OSPFv3, 414
OSPFv3 neighbor state change logging, 425
RIP (on interface), 29
RIP (on network), 28
RIP FRR BFD, 43
RIP NSR, 40
RIP poison reverse, 35
RIP split horizon, 35, 35
RIP update source IP address check, 36
RIPng FRR BFD, 397
RIPv1 incoming message zero field check, 35
RIPv2 automatic route summarization, 31
enhancing
IS-IS network security, 159
establishing
BGP session establishment disable, 269
EBGP session establishment (multiple hop), 261
excluding
OSPF interface from base topology, 85
exit overflow interval (OSPF), 91
extending
IS-IS LSP fragment extension, 153
MP-BGP MP_REACH_NLRI extended attribute,
201
MP-BGP MP_UNREACH_NLRI extended
attribute, 201

Table of Contents

Other manuals for HPE FlexNetwork 5510 HI Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HPE FlexNetwork 5510 HI Series and is the answer not in the manual?

HPE FlexNetwork 5510 HI Series Specifications

General IconGeneral
BrandHPE
ModelFlexNetwork 5510 HI Series
CategorySwitch
LanguageEnglish

Related product manuals