EasyManuals Logo

Huawei SmartAX MA5608T User Manual

Huawei SmartAX MA5608T
1979 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1417 background imageLoading...
Page #1417 background image
huawei(config)#clock priority system 0
2. Configure the 1588v2 time source (time synchronization).
a. Run the ptp enable command to enable the 1588v2 function.
huawei(config)#ptp enable
b. Run the ptp source command to add the 1588v2 clock source as the system clock
source.
huawei(config)#ptp source 0 0/0/1
c. Run the ptp priority command to configure the priority of the 1588v2 clock
source.
huawei(config)#ptp priority 0
3. Run the ptp port enable command to enable the 1588v2 function on the Ethernet port
to transmit 1588v2 packets on the specified port.
huawei(config)#ptp port 0/3/1 enable
4. Query the configuration and status of the 1588v2 clock source and system clock
source.
Run the display ptp source command to query the status of the 1588v2 clock
source.
Run the display clock source command to query the configuration and status of
the system clock source.
huawei(config)#display ptp source
---------------------------------------------------------------------
Index Type Source State Priority Selected Lock state
---------------------------------------------------------------------
0 1588 0/0/1 Normal 0 --- successful
1 -- -/ -/ - --- --- --- ---
2 -- -/ -/ - --- --- --- ---
3 -- -/ -/ - --- --- --- ---
4 -- -/ -/ - --- --- --- ---
5 -- -/ -/ - --- --- --- ---
6 -- -/ -/ - --- --- --- ---
7 -- -/ -/ - --- --- --- ---
8 -- -/ -/ - --- --- --- ---
9 -- -/ -/ - --- --- --- ---
---------------------------------------------------------------------
huawei(config)#display clock source
--------------------------------------------------------------------
Index Type Source State Priority QL Selected
--------------------------------------------------------------------
0 line 0/0/1 Normal 0 --- YES
1 -- -/ -/ - --- --- NO ---
2 -- -/ -/ - --- --- NO ---
3 -- -/ -/ - --- --- NO ---
4 -- -/ -/ - --- --- NO ---
5 -- -/ -/ - --- --- NO ---
6 -- -/ -/ - --- --- NO ---
7 -- -/ -/ - --- --- NO ---
8 -- -/ -/ - --- --- NO ---
9 -- -/ -/ - --- --- NO ---
--------------------------------------------------------------------
l Configure the ONU-side clock (the ONU provides the base station with a clock by
using the clock interface on the panel to implement time synchronization).
This configuration is applicable to time synchronization in the base station where
synchronous base station technologies (TDS-CDMA/CDMA2000/LTE is a representative)
are adopted. If a base station provides the ETH port but does not support 1588v2 packets,
the ONU outputs 1PPS+ToD time for the base station synchronization.
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
14 FTTM Configuration (Base Station Access)
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1392

Table of Contents

Other manuals for Huawei SmartAX MA5608T

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Huawei SmartAX MA5608T and is the answer not in the manual?

Huawei SmartAX MA5608T Specifications

General IconGeneral
Dual Power SupplyYes
Humidity5% to 95% (non-condensing)
Uplink Slots2
Maximum GPON Ports16
Input Voltage Range-38.4 V DC to -72 V DC
Device TypeOLT
Power Supply-48 V DC
Operating Temperature-25°C to +55°C
Storage Temperature-40°C to 70°C
Switching Capacity128 Gbps
PortsGPON, XG-PON, 10GE

Related product manuals