Huawei SmartAX MA5608T User Manual

Assume that the VDSL2 path mode is PTM mode, port is 0/1/0, and packets from the user
VLAN are untagged. Add a service flow as follows:
huawei(config)#service-port 301 vlan 300 vdsl mode ptm 0/1/0 multi-service user-
vlan untagged rx-cttr 10 tx-cttr 10
Step 22 Configure the multicast service.
huawei(config)#vlan 1000 smart
huawei(config)#port vlan 1000 0/0 1
huawei(config)#multicast-vlan 1000
huawei(config-mvlan1000)#igmp ipv6 version v2
huawei(config-mvlan1000)#igmp ipv6 mode proxy
Are you sure to change IGMP IPv6 mode?(y/n)[n]:y
huawei(config-mvlan1000)#igmp uplink-port 0/0/1
huawei(config-mvlan1000)#igmp program add batch ipv6 ff15:: to-ipv6 ff15::ffff
source-ipv6 2000::1
huawei(config-mvlan1000)#quit
Configure a service flow for the multicast service.
Configurations vary according to upstream interface types of HGWs.
l If HGWs are connected to an ONU upstream through LANs, assume that the user VLAN ID
is 43 and the Ethernet port is 0/3/1, and add a service flow as follows:
huawei(config)#service-port 401 vlan 1000 eth 0/3/1 multi-service user-vlan 43
rx-cttr 10 tx-cttr 10
l If HGWs are connected to an ONU upstream in ADSL2+ mode, assume that the VPI/VCI is
0/35 and the ADSL2+ port is 0/2/0, and add a service flow as follows:
huawei(config)#service-port 401 vlan 1000 adsl vpi 0 vci 35 0/2/0 multi-service
user-vlan untagged rx-cttr 10 tx-cttr 10
l If HGWs are connected to an ONU upstream in VDSL2 mode, assume that the VDSL2 path
mode is PTM mode, the user VLAN ID is 43, and the VDSL2 port is 0/1/0, and add a service
flow as follows:
huawei(config)#service-port 401 vlan 1000 vdsl mode ptm 0/1/0 multi-service user-
vlan 43 rx-cttr 10 tx-cttr 10
huawei(config-mvlan1000)#btv
huawei(config-btv)#igmp user add service-port 401 no-auth
huawei(config-btv)#multicast-vlan 1000
huawei(config-mvlan1000)#igmp multicast-vlan member service-port 401
huawei(config-mvlan1000)#quit
Step 23 Save the configuration on the ONU side.
huawei(config)#save
----End
19.5 Configuring IPv6 Services in the FTTH (Bridging ONT)
Scenario
This section describes the methods for configuring IPv6 services in the FTTH (bridging ONT)
scenario.
19.5.1 Application Scenarios
The FTTH (bridging ONT) supports multiple IPv6 HSI and IPTV service schemes.
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
19 IPv6 Configuration
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1915

Huawei SmartAX MA5608T Specifications

General

Dual Power Supply	Yes
Humidity	5% to 95% (non-condensing)
Uplink Slots	2
Maximum GPON Ports	16
Input Voltage Range	-38.4 V DC to -72 V DC
Device Type	OLT
Power Supply	-48 V DC
Operating Temperature	-25°C to +55°C
Storage Temperature	-40°C to 70°C
Switching Capacity	128 Gbps
Ports	GPON, XG-PON, 10GE