Huawei SmartAX MA5608T User Manual

3. Configure the multicast service
l Enable the multicast proxy function.
huawei(config)#multicast-vlan 100
huawei(config-mvlan100)#igmp mode proxy
Are you sure to change IGMP mode?(y/n)[n]:y
l Configure the upstream port.
huawei(config-mvlan100)#igmp uplink-port 0/19/0 100
huawei(config-mvlan100)#quit
huawei(config)#btv
huawei(config-btv)#igmp uplink-port-mode default
Are you sure to change the uplink port mode?(y/n)[n]:y
l Configure the preview parameters.
In this example, set the preview duration for program 1 to 150s, the number of
preview attempts to 6 each day, and the preview interval to 60s.
huawei(config-btv)#igmp preview-profile add index 1 duration 150 times 6
interval 60
huawei(config-btv)#igmp preview auto-reset-time 00:00:00
huawei(config-btv)#quit
l Configure the program library.
huawei(config)#multicast-vlan 100
huawei(config-mvlan100)#igmp program add name program1 ip 224.1.1.1
sourceip 10.10.10.10
huawei(config-mvlan100)#igmp program add name program2 ip 224.1.1.2
sourceip 10.10.10.10
huawei(config-mvlan100)#igmp program add name program3 ip 224.1.1.3
sourceip 10.10.10.10 preview-profile 1
huawei(config-mvlan100)#quit
l Configure the authority profile.
huawei(config)#btv
huawei(config-btv)#igmp profile add profile-name profile0
huawei(config-btv)#igmp profile profile-name profile0 program-name program1
watch
huawei(config-btv)#igmp profile profile-name profile0 program-name program2
watch
huawei(config-btv)#igmp profile profile-name profile0 program-name program3
preview
l Configure the multicast user.
huawei(config-btv)#igmp user add port 0/2/3 no-auth
huawei(config-btv)#igmp user add port 0/2/2 auth
huawei(config-btv)#igmp user bind-profile port 0/2/16 profile-name profile0
huawei(config-btv)#quit
huawei(config)#multicast-vlan 100
huawei(config-mvlan100)#igmp multicast-vlan member port 0/2/2
huawei(config-mvlan100)#igmp multicast-vlan member port 0/2/3
huawei(config-btv)#quit
Step 11 Save the data.
huawei(config)#save
----End
7.6 Configuring MA5600T-4
This topic describes how to configure MA5600T-4.
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
7 Example: Subtending Networking
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
537

Huawei SmartAX MA5608T Specifications

General

Dual Power Supply	Yes
Humidity	5% to 95% (non-condensing)
Uplink Slots	2
Maximum GPON Ports	16
Input Voltage Range	-38.4 V DC to -72 V DC
Device Type	OLT
Power Supply	-48 V DC
Operating Temperature	-25°C to +55°C
Storage Temperature	-40°C to 70°C
Switching Capacity	128 Gbps
Ports	GPON, XG-PON, 10GE