huawei(config-acl-adv-3050)#rule permit ip source 3.3.3.3 0.0.0.0
destination 10.10.1.2 0.0.0.0
huawei(config-acl-adv-3050)#rule permit ip source 3.3.4.3 0.0.0.0
destination 10.10.1.2 0.0.0.0
huawei(config-acl-adv-3050)#quit
huawei(config)#packet-filter inbound ip-group 3050 port 0/19/0
huawei(config)#packet-filter inbound ip-group 3050 port 0/19/1
4. Configure SNMP.
l Set the community name and access authority.
huawei(config)#snmp-agent community read public
huawei(config)#snmp-agent community write private
l Set the SysContact.
huawei(config)#snmp-agent sys-info contact HW-075512345678
l Set the SysLocation.
huawei(config)#snmp-agent sys-info location Shenzhen China
l Set the SNMP version.
The SNMP version must be the same as the SNMP version of the NMS. In this
example, the SNMP version is set as SNMP V2C.
huawei(config)#snmp-agent sys-info version v2c
5. Enable the trap sending.
huawei(config)#snmp-agent trap enable standard
6. Set trap destination address.
huawei(config)#snmp-agent target-host trap-hostname huawei address 2.2.2.2
trap-paramsname abc
huawei(config)#snmp-agent target-host trap-hostname huawei123 address 2.2.2.3
trap-paramsname 123
7. Set the trap source address.
huawei(config)#snmp-agent trap source vlanif 10
Step 3 Configure the time server.
huawei(config)#ntp-service unicast-server 4.4.4.4 source-interface vlanif 10
huawei(config)#ntp-service unicast-server 4.4.4.5 source-interface vlanif 10
Step 4 Configure the log host.
huawei(config)#loghost add 3.3.3.3 syslog-1
huawei(config)#loghost activate ip 3.3.3.3
huawei(config)#loghost add 3.3.4.3 syslog-2
huawei(config)#loghost activate ip 3.3.4.3
Step 5 Configure the EMU.
This topic uses the fan monitoring as an example to show how to configure the EMU.
By default, the default slave node number of the fan EMU is 0. In this example, assume that the
slave node number is 1. In this case, you need to set the DIP switch of the node address on the
fan monitoring unit as 1.
huawei(config)#emu add 0 h801ESC 0 0
huawei(config)#emu add 1 fan 0 1
Step 6 Configure the ADSL2+ service.
The MA5600T supports the ADSL2+ service of multiple encapsulation modes, such as IPoA,
PPPoA, IPoE, and PPPoE. This topic uses the PPPoE mode as an example to describe how to
configure the ADSL2+ service. For other encapsulation modes, see "3.1 Example: Configuring
the xDSL Internet Access Service."
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
7 Example: Subtending Networking
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
531
To Next Page
Loading...
Need help?
General
