Komatsu PC2000-8 - Page 499

INDEX
8-3
INDEX
18
<A>
ACCUMULATOR.........................................................3-148
AFTER STARTING ENGINE.......................................3-192
AIR CONDITIONER CONTROLS................................3-113
ASHTRAY....................................................................3-111
ATTACHMENT GUIDE....................................................6-4
COMBINATIONS OF WORK EQUIPMENT ...............6-4
AUXILIARY ELECTRIC POWER.................................3-133
<B>
BEFORE READING THIS MANUAL ...............................1-2
BEFORE STARTING ENGINE....................................3-158
BUCKET REPLACEMENT ..........................................3-229
<C>
CAP WITH LOCK ........................................................3-109
CHECK BEFORE SHUT OFF ENGINE.......................3-232
CIRCUIT BREAKER....................................................3-136
COLD WEATHER OPERATION..................................3-235
AFTER COLD WEATHER SEASON......................3-237
AFTER DAILY WORK COMPLETION....................3-237
COLD WEATHER OPERATION INFORMATION ..3-235
COMBINATION OF WORK EQUIPMENT.....................7-22
COMBINATION OF WORK EQUIPMENT................7-22
CONTROL LEVERS AND PEDALS ............................3-102
CONTROLLER ............................................................3-140
CONTROLS AND GAUGES............................................3-3
<D>
DETAILED CONTROLS AND GAUGES .........................3-7
DIRECTIONS OF MACHINE...........................................1-6
DOOR LOCK ...............................................................3-104
<E>
ELECTRIC SYSTEM MAINTENANCE............................4-9
EMERGENCY ESCAPE HAMMER.............................3-105
EMERGENCY EXIT FROM OPERATORSCAB' .........3-104
End of Service Life.........................................................2-44
EPA REGULATIONS, ENGINE NUMBER PLATE........1-10
ESCAPE FROM MUD .................................................3-227
EXCAVATOR WORK ....................................................7-11
EXPLANATION OF COMPONENTS...............................7-3
<F>
FIRE EXTINGUISHER.................................................3-109
FUSE ...........................................................................3-134
FUSE (IF EQUIPPED).................................................3-139
<G>
GENERAL OPERATION INFORMATION ...................3-224
GENERAL PRECAUTIONS COMMON TO OPERATION
AND MAINTENANCE...............................................2-11
DO NOT GET CAUGHT IN WORK EQUIPMENT....2-16
FIRE PREVENTION.................................................2-13
PRECAUTIONS BEFORE STARTING
OPERATION ............................................................2-11
PRECAUTIONS RELATED TO ATTACHMENTS AND
OPTIONS .................................................................2-17
PRECAUTIONS RELATED TO CAB GLASS...........2-18
PRECAUTIONS RELATED TO PROTECTIVE
STRUCTURES.........................................................2-16
PRECAUTIONS WHEN GETTING ON OR OFF
MACHINE.................................................................2-14
PRECAUTIONS WHEN RUNNING ENGINE INSIDE
BUILDING.................................................................2-18
PREPARATIONS FOR SAFE OPERATION ............2-11
PROTECTION AGAINST FALLING, FLYING,
INTRUDING OBJECTS............................................2-17
UNAUTHORIZED MODIFICATION..........................2-17
GENERAL PRECAUTIONS FOR SAFETY.....................6-2
PRECAUTIONS WHEN REMOVING OR
INSTALLING...............................................................6-2
PRECAUTIONS WHEN SELECTING ........................6-2
PRECAUTIONS WHEN USING .................................6-3
READ THE INSTRUCTION MANUAL
THOROUGHLY ..........................................................6-2
<H>
HANDLING EMERGENCY LADDER ..........................3-106
ESCAPE PROCEDURE.........................................3-106
PRECAUTION WHEN STORING ROPE LADDER 3-108
HANDLING FUEL QUICK CHARGE...............................6-6
ACTION WHEN MACHINE DOES NOT MOVE
BECAUSE OF FAILURE IN PROXIMITY SWITCH..6-11
GENERAL LOCATIONS.............................................6-6
PROCEDURE FOR OPERATING FUEL CHARGE ...6-7
REPLACE FUEL TANK BREATHER ELEMENT .....6-10
HANDLING GREASE PUMP AND GREASE GUN.....3-141
HANDLING HYDRAULIC LADDER.............................3-150
ACTION WHEN MACHINE DOES NOT MOVE
BECAUSE OF FAILURE IN PROXIMITY SWITCH3-152
PROCEDURE FOR OPERATING HYDRAULIC
LADDER.................................................................3-150
HANDLING JUMP START RECEPTACLE....................6-36
CONNECTED PROCEDURE OF EXTERNAL POWER
SOURCE ..................................................................6-36
GENERAL LOCATIONS...........................................6-36
HANDLING MACHINES EQUIPPED WITH VHMS.....3-156
HANDLING OIL, FUEL, COOLANT, AND PERFORMING
OIL CLINIC.................................................................4-5
HANDLING SERVICE CENTER....................................6-15
ACTION WHEN MACHINE DOES NOT MOVE
BECAUSE OF FAILURE IN PROXIMITY SWITCH..6-32
GENERAL LOCATIONS...........................................6-15
GREASING LADDER SERVICE ARM .....................6-30
METHOD OF DRAINING, ADDING LUBRICANT AND
COOLANT FROM SERVICE PANEL.......................6-19
PROCEDURE FOR OPERATING SERVICE ARM..6-16
REPLACE FUEL TANK BREATHER ELEMENT .....6-31
<I>
INTRODUCTION.............................................................1-6