Leader LT4670 - Setting the NTP Server

To Next Page

To Previous Page

14 SYSTEM CONFIG MENU

142

14.3.8 Setting the NTP Server

To set the NTP server address, follow the procedure below.

Procedure

SYSTEM CONFIG > NETWORK > NTP > NTP SERVER ADDRESS

Parameters

000.000.000.000 - 255.255.255.255

Initial value

000.000.000.000

3 . N T P S E R V E R A D D R E S S

　 0 0 0 . 0 0 0 . 0 0 0 . 0 0 0

Main Page

Default Chapter2
- Table of Contents2
General Safety Summary10
1 Introduction14
- User Registration14
- Scope of Warranty14
- Trademark Acknowledgments14
- Operating Precautions15
2 Product Configuration16
- Main Unit16
- Hardware Options16
- Software Options17
3 Specifications18
- General18
- Features18
- Standards24
4 Panel Description43
- Front Panel43
- Rear Panel46
5 Preparations49
- Turning the Power on49
- Rack Mounting53
6 Basic Operation54
- Operation Basics54
- Signal Input (Genlock Operation)58
- SDI Signal Output68
- LTC Signal I/O and Remote Control71
- Alarm Display73
- L-Sync74
7 Reference Config Menu76
- Selecting the Reference Signal76
- Selecting the Genlock Format77
- Setting the Genlock Timing78
- Selecting the Satellite (SER01)78
- Setting the Recovery Operation79
- Setting the Relock80
- Selecting the Time Source81
- Loading the Date and Time82
8 Black Config Menu83
- Selecting the Black Format83
- Configuring Timing Data84
- Setting the Time Code85
  - Turning Time Code Insertion on and off85
  - Setting Dropped Frames86
- Setting the Black Output86
  - Turning the Black Output on and off86
  - Turning BMCA Linkage on and off (SER03)87
- Settings Shared by Black Outputs87
9 Audio Config Menu88
- Setting the AES/EBU Output88
- Setting the Silence Output91
- Setting the Word-Clock Output93
  - Adjusting the Timing93
10 Ltc Config Menu94
- Turning the LTC Output on and off94
- Selecting the LTC Format94
- Adjusting the Timing (Frame)95
- Adjusting the Timing (Bit)95
- Adjusting the Offset95
- Setting Dropped Frames96
- Settings Shared by LTC Outputs96
11 Cw/1Pps Config Menu97
- Switching the Output Signal97
12 Sdi Config Menu (Ser02)98
- Selecting the Frequency Group98
- Setting the SDI Format99
- Configuring Timing Data101
- Selecting the Pattern102
- Turning Ycbcr/Gbr on and off104
- Turning Safety Area Markers on and off105
- Configuring the Pattern Scroll Feature106
- Setting the Pattern Change107
  - Turning Pattern Change on and off107
  - Setting the Change Interval108
- Setting ID Characters108
- Setting the Moving Box116
- Setting a Circle119
- Setting the Time Code122
- Turning Lip Sync on and off124
- Configuring Embedded Audio126
- Setting Ancillary Data130
- Setting the SDI Output131
  - Turning the SDI Output on and off131
  - Turning BMCA Linkage on and off (SER03)132
- Settings Shared by SDI Outputs132
13 Ptp Config Menu (Ser03)133
- PTP Leader and PTP Follower133
- Setting the PTP Leader133
- Setting the PTP Follower140
14 System Config Menu147
- Setting the Backlight147
- Configuring Presets147
- Setting the Network152
- Setting the Time156
- Setting the GNSS (SER01)160
  - Setting the Power Supply160
  - Setting the Cable Delay160
- Configuring the PTP Settings (SER03)161
- Setting the Alarm163
  - Selecting the Polarity163
  - Turning the Alarm Output on and off164
- Configuring the Log165
- Initialization166
- Viewing and Adding Software Options168
  - Viewing Software Options168
  - Adding Software Options168
- Configuring USB169
- Turning the Fans on and off169
- Copying the System Settings170
  - Copying System Settings from a USB Memory Device to the Instrument170
  - Copying System Settings from the Instrument to a USB Memory Device170
15 Status Menu171
- ALARM Menu171
- INFORMATION Menu172
- CONFIG Menu174
- LOG Menu178
  - Viewing the Log178
  - Clearing the Log178
16 Web Browser179
- Operating Environment179
- How to Use179
- Procedure181
- Screen Description183
17 Maintenance201
- Calibration and Repair201
- Replacement of Parts201
18 Appendix209
- List of Settings209
- Release Notes216

Leader LT4670 - Setting the NTP Server

Table of Contents

Other manuals for Leader LT4670

Related product manuals